Central Locking Module Replacement - Revision history

Thorburn: Catagories added

2012-01-19T12:34:54Z

Catagories added

← Older revision		Revision as of 12:34, 19 January 2012
Line 38:		Line 38:

	Thanks to all those that replied on [http://forums.seloc.org/viewthread.php?tid=199857 this thread] and others for the information on how to do this.		Thanks to all those that replied on [http://forums.seloc.org/viewthread.php?tid=199857 this thread] and others for the information on how to do this.

			[[Category:Lotus Elise]]
			[[Category:S2]]
			[[Category:S2 Exige]]
			[[Category:Lotus Europa]]

yod at 12:36, 22 January 2010

2010-01-22T12:36:13Z

← Older revision		Revision as of 12:36, 22 January 2010
Line 7:		Line 7:
	[[Image:CDLModuleReplace-EndTabs.jpg\|left\|thumb\|End Tabs]]		[[Image:CDLModuleReplace-EndTabs.jpg\|left\|thumb\|End Tabs]]
	<br><br><br><br><br><br><br><br><br><br>		<br><br><br><br><br><br><br><br><br><br>
	The procedure is fairly simple but it's not very easy to do because of the limited access. You have to stick your hand in through the side window vent hole - my hand was a tight fit but once it was in there was enough space to work. If you've got bigger hands or wrists it would be a lot more difficult. Also, the edges of the bits of aluminium a pretty sharp so be careful.		The procedure is fairly simple but it's not very easy to do because of the limited access. You have to stick your hand in through the side window vent hole - my hand was a tight fit but once it was in there was enough space to work. If you've got bigger hands or wrists it would be a lot more difficult. Also, the edges of the bits of aluminium are pretty sharp so be careful.

	==Procedure==		==Procedure==

yod at 17:43, 20 December 2009

2009-12-20T17:43:36Z

← Older revision		Revision as of 17:43, 20 December 2009
Line 13:		Line 13:
	[[Image:CDLModuleReplace1.jpg\|left\|thumb\|Light switch panel removed]]		[[Image:CDLModuleReplace1.jpg\|left\|thumb\|Light switch panel removed]]
	Unscrew the 4 torx screws holding the panel in and move it to one side. You can disconnect the switches or just be careful not to pull the wires too hard.		Unscrew the 4 torx screws holding the panel in and move it to one side. You can disconnect the switches or just be careful not to pull the wires too hard.
	<br><br><br><br><br><br><br><br><br>		<br><br><br><br><br><br><br><br><br><br><br>
	[[Image:CDLModuleReplace2.jpg\|left\|thumb\|Light switch panel removed 2]]		[[Image:CDLModuleReplace2.jpg\|left\|thumb\|Light switch panel removed 2]]
	You'll then be faced with the hose that carries the air to the side window vent. This needs to be moved as the module is behind it.		You'll then be faced with the hose that carries the air to the side window vent. This needs to be moved as the module is behind it.

yod at 17:42, 20 December 2009

2009-12-20T17:42:58Z

← Older revision		Revision as of 17:42, 20 December 2009
Line 19:		Line 19:
	===Move vent hose===		===Move vent hose===
	[[Image:CDLModuleReplace3.jpg\|left\|thumb\|Move vent hose 1]]		[[Image:CDLModuleReplace3.jpg\|left\|thumb\|Move vent hose 1]]
	The vent hose needs to be moved to the left as you look at it. It's fixed by 2 plastic tabs - one at the top and one at the bottom - that fit into slots in the aluminium. It requires quite a bit of force to get it out - I managed to do it by twisting the whole end part ~~clockwise~~ and bending it slightly.		The vent hose needs to be moved to the left as you look at it. It's fixed by 2 plastic tabs - one at the top and one at the bottom - that fit into slots in the aluminium. It requires quite a bit of force to get it out - I managed to do it by twisting the whole end part anticlockwise and bending it slightly.
	<br><br><br><br><br><br><br><br><br>		<br><br><br><br><br><br><br><br><br>
	[[Image:CDLModuleReplace4.jpg\|left\|thumb\|Move vent hose 2]]		[[Image:CDLModuleReplace4.jpg\|left\|thumb\|Move vent hose 2]]

yod9999 at 21:04, 27 January 2009

2009-01-27T21:04:38Z

← Older revision		Revision as of 21:04, 27 January 2009
Line 3:		Line 3:
	The part number needed is A116M6048F. You can get this from a Lotus dealer - I paid £38.71 from Lispcomb.		The part number needed is A116M6048F. You can get this from a Lotus dealer - I paid £38.71 from Lispcomb.

	The module itself looks like this. You can see that the circuit board is held into the case by 4 tabs - one on each side. The existing case will be left in the car and just the circuit board replaced (these pics are from [http://forums.seloc.org/member.php?action=viewpro&member=monkski monski] - cheers).		The module itself looks like this. You can see that the circuit board is held into the case by 4 tabs - one on each side. The existing case will be left in the car and just the circuit board replaced (these two pics are from [http://forums.seloc.org/member.php?action=viewpro&member=monkski monski] - cheers).
	[[Image:CDLModuleReplace-CDM.jpg\|left\|thumb\|CDM]]		[[Image:CDLModuleReplace-CDM.jpg\|left\|thumb\|CDM]]
	[[Image:CDLModuleReplace-EndTabs.jpg\|left\|thumb\|End Tabs]]		[[Image:CDLModuleReplace-EndTabs.jpg\|left\|thumb\|End Tabs]]

yod9999 at 21:04, 27 January 2009

2009-01-27T21:04:03Z

New page

Instructions for replacing the Central Locking Module (CDL Module in Lotus-speak). These instructions are for a 05 Elise 111R, but it's probably very similar for other models. If you go to a dealer to get this done they do it the correct way by taking the whole dash apart and they charge 4 hours labour. I did this using the procedure below in 45 minutes without losing any blood.

The part number needed is A116M6048F. You can get this from a Lotus dealer - I paid £38.71 from Lispcomb.

The module itself looks like this. You can see that the circuit board is held into the case by 4 tabs - one on each side. The existing case will be left in the car and just the circuit board replaced (these pics are from [http://forums.seloc.org/member.php?action=viewpro&member=monkski monski] - cheers).
[[Image:CDLModuleReplace-CDM.jpg|left|thumb|CDM]]
[[Image:CDLModuleReplace-EndTabs.jpg|left|thumb|End Tabs]]
 
The procedure is fairly simple but it's not very easy to do because of the limited access. You have to stick your hand in through the side window vent hole - my hand was a tight fit but once it was in there was enough space to work. If you've got bigger hands or wrists it would be a lot more difficult. Also, the edges of the bits of aluminium a pretty sharp so be careful.

==Procedure==
===Remove light switch panel===
[[Image:CDLModuleReplace1.jpg|left|thumb|Light switch panel removed]]
Unscrew the 4 torx screws holding the panel in and move it to one side. You can disconnect the switches or just be careful not to pull the wires too hard.
 
[[Image:CDLModuleReplace2.jpg|left|thumb|Light switch panel removed 2]]
You'll then be faced with the hose that carries the air to the side window vent. This needs to be moved as the module is behind it.
 
===Move vent hose===
[[Image:CDLModuleReplace3.jpg|left|thumb|Move vent hose 1]]
The vent hose needs to be moved to the left as you look at it. It's fixed by 2 plastic tabs - one at the top and one at the bottom - that fit into slots in the aluminium. It requires quite a bit of force to get it out - I managed to do it by twisting the whole end part clockwise and bending it slightly.
 
[[Image:CDLModuleReplace4.jpg|left|thumb|Move vent hose 2]]
Once you've freed it push it out of the way to the left.
 
===Remove module===
[[Image:CDLModuleReplace5.jpg|left|thumb|Module 1]]
[[Image:CDLModuleReplace6.jpg|none|thumb|Module 2]]
 
You can now see the module. It's on the right under the big bit of foam with the orange wire sticking out of it. You need to unplug the module, the connector seemed to come off quite easily with a bit of wiggling. To get the circuit board out of the case I just jammed a smallish screwdriver down the left side of the circuit board and levered it out bit by bit.

Once the board is out you can put the new one in. The bit of grey foam gets in the way here, I managed to use the CDL connector to hold the foam up out of the way so I could get the new board in. It's quite tricky as you can't see what you're doing so you have to do it by feel.

Test that the new module works as expected.

===Put it all back together===
Once it's in you just need to put everything back. The hose is a PITA to get back, but it just needs a bit of force to get it back in place. Then put the switch panel back in, carefully pushing all the wires back in to the gap where they came from. Before screwing it all back together be sure to check that the switches all still work as I managed to disconnect the headlight switch by accident.

Thanks to all those that replied on [http://forums.seloc.org/viewthread.php?tid=199857 this thread] and others for the information on how to do this.