Change the ignition switch - Revision history

Noisy Tim: /* S1 */

2024-04-07T07:34:24Z

← Older revision		Revision as of 07:34, 7 April 2024
Line 6:		Line 6:
	The ignition switch used in the Elise S1 is like the rest of the steering column from GM/Vauxhall/Opel (e.g. Corsa B). The GM spare part number is 914852 or 90389377.<br/>		The ignition switch used in the Elise S1 is like the rest of the steering column from GM/Vauxhall/Opel (e.g. Corsa B). The GM spare part number is 914852 or 90389377.<br/>
	<br/>		<br/>
	'''IMPORTANT!!! To remove/insert the ignition lock and/or switch ensure the key is inserted and is set to position I''' (key vertical and position where normally the radio is on but ignition is still off).<br/>		'''IMPORTANT!!! To remove/insert the ignition lock and/or switch ensure the key is inserted and is set to position I''' (key vertical and position where normally the radio is on but ignition is still off). On a 2004 111S, (and probably other years and models too), it has to be in position 2.<br/>
	<br/>		<br/>
	=== Ignition lock ===		=== Ignition lock ===

Eton at 08:44, 27 January 2014

2014-01-27T08:44:10Z

Eton at 21:29, 26 January 2014

2014-01-26T21:29:51Z

← Older revision		Revision as of 21:29, 26 January 2014
Line 37:		Line 37:
	==== Assemble the ignition switch ====		==== Assemble the ignition switch ====
	# Use the (removed) ignition lock to ensure the switch is set to position I and the latch can be pressed in (see picture)		# Use the (removed) ignition lock to ensure the switch is set to position I and the latch can be pressed in (see picture)
	# Insert in the switch on the dowel and screw in grub screw. Don't fully tighten yet.		# Insert in the switch on the dowel and screw in the grub screw. Don't fully tighten yet.
	# Insert the ignition lock (see above)		# Insert the ignition lock (see above)
	# Tighten the grub screw		# Tighten the grub screw

Eton at 21:29, 26 January 2014

2014-01-26T21:29:05Z

← Older revision		Revision as of 21:29, 26 January 2014
Line 33:		Line 33:
	# Use a small screwdriver and press as shown in the picture to unlatch the plug (only possible if the switch had been set to position I)		# Use a small screwdriver and press as shown in the picture to unlatch the plug (only possible if the switch had been set to position I)
	# Unscrew the grub screw and remove without dropping it		# Unscrew the grub screw and remove without dropping it
	# ~~If the ignition lock~~ is ~~removed~~ the ~~ignition~~ switch ~~can be unfastened~~		# The switch is now only held by a small dowel. Move the switch towards the steering wheel to get it off the dowel and remove it
	<br/>		<br/>
	==== Assemble the ignition switch ====		==== Assemble the ignition switch ====

Eton at 21:16, 26 January 2014

2014-01-26T21:16:05Z

← Older revision		Revision as of 21:16, 26 January 2014
Line 33:		Line 33:
	# Use a small screwdriver and press as shown in the picture to unlatch the plug (only possible if the switch had been set to position I)		# Use a small screwdriver and press as shown in the picture to unlatch the plug (only possible if the switch had been set to position I)
	# Unscrew the grub screw and remove without dropping it		# Unscrew the grub screw and remove without dropping it
	# If the ignition lock is removed the ignition switch can be ~~left out~~		# If the ignition lock is removed the ignition switch can be unfastened
	<br/>		<br/>
	==== Assemble the ignition switch ====		==== Assemble the ignition switch ====
	# Use the (removed) ignition lock to ensure the switch is set to position I and the latch can be pressed in (see picture)		# Use the (removed) ignition lock to ensure the switch is set to position I and the latch can be pressed in (see picture)
	# ~~Leave~~ in the switch on the dowel and ~~insert~~ grub screw. Don't fully tighten yet.		# Insert in the switch on the dowel and screw in grub screw. Don't fully tighten yet.
	# Insert the ignition lock (see above)		# Insert the ignition lock (see above)
	# Tighten the grub screw		# Tighten the grub screw

Stu at 20:45, 26 January 2014

2014-01-26T20:45:48Z

Stu at 20:40, 26 January 2014

2014-01-26T20:40:40Z

← Older revision		Revision as of 20:40, 26 January 2014
Line 4:		Line 4:
	<br/>		<br/>
	== S1 ==		== S1 ==
	The ~~ingition~~ switch used in the Elise S1 is like the rest of the steering column from GM/Vauxhall/Opel (e.g. Corsa B). The GM spare part number is 914852 or 90389377.<br/>		The ignition switch used in the Elise S1 is like the rest of the steering column from GM/Vauxhall/Opel (e.g. Corsa B). The GM spare part number is 914852 or 90389377.<br/>
	<br/>		<br/>
	'''IMPORTANT!!! To remove/insert the ignition lock and/or switch ensure the key is inserted and is set to position I''' (key vertical and position where normally the radio is on but ignition is still off).<br/>		'''IMPORTANT!!! To remove/insert the ignition lock and/or switch ensure the key is inserted and is set to position I''' (key vertical and position where normally the radio is on but ignition is still off).<br/>
Line 28:		Line 28:
	[[File:Zuendschalter.jpg\|right\|thumb\|240px\|Direction to unlock the ignition switch]]		[[File:Zuendschalter.jpg\|right\|thumb\|240px\|Direction to unlock the ignition switch]]
	[[File:Zuend_3.jpg\|right\|thumb\|240px\|Unscrew the ignition switch fix grub screw]]		[[File:Zuend_3.jpg\|right\|thumb\|240px\|Unscrew the ignition switch fix grub screw]]
	# Disconnect the ~~batterie~~		# Disconnect the battery
	# Remove the ignition lock (see above)		# Remove the ignition lock (see above)
	# Use a small screw driver to remove the ignition switch cover or unlock switch with the cover mounted (more fiddly but possible - see picture)		# Use a small screw driver to remove the ignition switch cover or unlock switch with the cover mounted (more fiddly but possible - see picture)
Line 36:		Line 36:
	<br/>		<br/>
	==== Assemble the ignition switch ====		==== Assemble the ignition switch ====
	# Use the (removed) ~~ingition~~ lock to ensure the switch is set to position I and the latch can be pressed in (see picture)		# Use the (removed) ignition lock to ensure the switch is set to position I and the latch can be pressed in (see picture)
	# Weave in the switch on the dowel and insert grub screw. ~~Dont~~' fully tighten jet.		# Weave in the switch on the dowel and insert grub screw. Don't fully tighten jet.
	# Insert the ignition lock (see above)		# Insert the ignition lock (see above)
	# Tighten the grub screw		# Tighten the grub screw
	# If you removed the cover of the plug reattach it		# If you removed the cover of the plug reattach it
	# Press the plug in the switch until it latches		# Press the plug in the switch until it latches
	# Reconnect the ~~batterie~~ and test ~~swicht~~		# Reconnect the battery and test switch
	# Reattach the shroud		# Reattach the shroud

Eton at 16:37, 26 January 2014

2014-01-26T16:37:57Z

← Older revision		Revision as of 16:37, 26 January 2014
Line 1:		Line 1:
	[[~~Categorie~~:Electrical]] [[~~Categorie~~:~~Elise~~ S1]]		[[Category:Electrical]] [[Category:S1]]

	The ignition switch can wear which can cause malfunction (e.g. no starter).<br/>		The ignition switch can wear which can cause malfunction (e.g. no starter).<br/>

Eton: Created page with "Categorie:Electrical Categorie:Elise S1 The ignition switch can wear which can cause malfunction (e.g. no starter).

== S1 == The ingition switch used in th..."

2014-01-26T16:36:47Z

Created page with "Categorie:Electrical Categorie:Elise S1 The ignition switch can wear which can cause malfunction (e.g. no starter). == S1 == The ingition switch used in th..."

New page

[[Categorie:Electrical]] [[Categorie:Elise S1]]

The ignition switch can wear which can cause malfunction (e.g. no starter). 
 
== S1 ==
The ingition switch used in the Elise S1 is like the rest of the steering column from GM/Vauxhall/Opel (e.g. Corsa B). The GM spare part number is 914852 or 90389377. 
 
'''IMPORTANT!!! To remove/insert the ignition lock and/or switch ensure the key is inserted and is set to position I''' (key vertical and position where normally the radio is on but ignition is still off). 
 
=== Ignition lock ===
==== Remove the ignition lock ====
[[File:Zuend_1.jpg|right|thumb|240px|Position of the key and unlatch the lock]]
# Remove the column shroud (7 screws and 1 nut for the trip switch)
# Insert key and set to position I (key must be vertical - see picture)
# At the front side (the side where the steering wheel is) of the outer barrel is a small hole. Press the short side of a small allen key into the hole (see picture). At the same time press the lock with the key towards the column gently wiggle the lock until is comes loose. The lock is pressed out by spring tension.
 
==== Insert the ignition lock ====
[[File:Zuend_4.jpg|right|thumb|240px|Unlatch the steering wheel lock]]
# Before inserting the ignition lock make sure the steering wheel lock is disengaged. Use a small screw driver to push the mechanism downwards until it locks into place (see picture)
# Ensure the key is inserted and is set to position I. Test if the locking notch on top of the ignition lock can be presses in until it is even with the outer shape of the lock.
# Press the lock into the barrel until it locks into place
# Check function and reattach the shroud
 
 
=== Ignition switch ===
==== Remove the ignition switch ====
[[File:Zuend_2.jpg|right|thumb|240px|Direction to unlock the ignition switch]]
[[File:Zuendschalter.jpg|right|thumb|240px|Direction to unlock the ignition switch]]
[[File:Zuend_3.jpg|right|thumb|240px|Unscrew the ignition switch fix grub screw]]
# Disconnect the batterie
# Remove the ignition lock (see above)
# Use a small screw driver to remove the ignition switch cover or unlock switch with the cover mounted (more fiddly but possible - see picture)
# Use a small screw driver and press as shown in the picture to unlatch the plug (only possible if the switch had been set to position I)
# Unscrew the grub screw and remove without dropping it
# If the ignition lock is removed the ignition switch can be weaved out
 
==== Assemble the ignition switch ====
# Use the (removed) ingition lock to ensure the switch is set to position I and the latch can be pressed in (see picture)
# Weave in the switch on the dowel and insert grub screw. Dont' fully tighten jet.
# Insert the ignition lock (see above)
# Tighten the grub screw
# If you removed the cover of the plug reattach it
# Press the plug in the switch until it latches
# Reconnect the batterie and test swicht
# Reattach the shroud

← Older revision		Revision as of 08:44, 27 January 2014
Line 13:		Line 13:
	# Remove the column shroud (7 screws and 1 nut for the trip switch)		# Remove the column shroud (7 screws and 1 nut for the trip switch)
	# Insert key and set to position I (key must be vertical - see picture)		# Insert key and set to position I (key must be vertical - see picture)
	# At the front side (the side where the steering wheel is) of the outer barrel is a small hole. Press the short side of a small allen key into the hole (see picture). At the same time press the lock ~~with~~ the key towards the column gently wiggle the lock until is comes loose. The lock is pressed out by spring tension.		# At the front side (the side where the steering wheel is) of the outer barrel is a small hole. Press the short side of a small allen key into the hole (see picture). At the same time press the lock by the key towards the column and gently wiggle the lock until is comes loose. The lock is pressed out by spring tension.
	<br/>		<br/>
	==== Insert the ignition lock ====		==== Insert the ignition lock ====
Line 26:		Line 26:
	==== Remove the ignition switch ====		==== Remove the ignition switch ====
	[[File:Zuend_2.jpg\|right\|thumb\|240px\|Direction to unlock the ignition switch]]		[[File:Zuend_2.jpg\|right\|thumb\|240px\|Direction to unlock the ignition switch]]
	[[File:Zuendschalter.jpg\|right\|thumb\|240px\|Direction to ~~unlock~~ the ~~ignition switch~~]]		[[File:Zuendschalter.jpg\|right\|thumb\|240px\|Direction to unlatch the plug]]
	[[File:Zuend_3.jpg\|right\|thumb\|240px\|Unscrew the ignition switch fix grub screw]]		[[File:Zuend_3.jpg\|right\|thumb\|240px\|Unscrew the ignition switch fix grub screw]]
	# Disconnect the battery		# Disconnect the battery
	# Remove the ignition lock (see above)		# Remove the ignition lock (see above)
	# Use a small screwdriver to remove the ignition switch cover or unlock switch with the cover mounted (more fiddly but possible - see picture)		# Use a small screwdriver to remove the ignition switch cover or unlock switch with the cover mounted (more fiddly but possible - see picture)
	# Use a small screwdriver and press as shown in the picture to unlatch the plug (only possible if the switch had been set to position I)		# Use a small screwdriver and press as shown in the picture to unlatch the plug (only possible if the switch had been set to position I) and disconnect the plug
	# Unscrew the grub screw and remove without dropping it		# Unscrew the grub screw and remove without dropping it
	# The switch is now only held by a small dowel. Move the switch towards the steering wheel to get it off the dowel and remove it		# The switch is now only held by a small dowel. Move the switch towards the steering wheel to get it off the dowel and remove it.
	<br/>		<br/>
	==== Assemble the ignition switch ====		==== Assemble the ignition switch ====

← Older revision		Revision as of 20:45, 26 January 2014
Line 17:		Line 17:
	==== Insert the ignition lock ====		==== Insert the ignition lock ====
	[[File:Zuend_4.jpg\|right\|thumb\|240px\|Unlatch the steering wheel lock]]		[[File:Zuend_4.jpg\|right\|thumb\|240px\|Unlatch the steering wheel lock]]
	# Before inserting the ignition lock make sure the steering wheel lock is disengaged. Use a small ~~screw driver~~ to push the mechanism downwards until it locks into place (see picture)		# Before inserting the ignition lock make sure the steering wheel lock is disengaged. Use a small screwdriver to push the mechanism downwards until it locks into place (see picture)
	# Ensure the key is inserted and is set to position I. Test if the locking notch on top of the ignition lock can be ~~presses~~ in until it is ~~even~~ with the outer shape of the lock.		# Ensure the key is inserted and is set to position I. Test if the locking notch on top of the ignition lock can be pressed in until it is level with the outer shape of the lock.
	# Press the lock into the barrel until it locks into place		# Press the lock into the barrel until it locks into place
	# Check function and reattach the shroud		# Check function and reattach the shroud
Line 30:		Line 30:
	# Disconnect the battery		# Disconnect the battery
	# Remove the ignition lock (see above)		# Remove the ignition lock (see above)
	# Use a small ~~screw driver~~ to remove the ignition switch cover or unlock switch with the cover mounted (more fiddly but possible - see picture)		# Use a small screwdriver to remove the ignition switch cover or unlock switch with the cover mounted (more fiddly but possible - see picture)
	# Use a small ~~screw driver~~ and press as shown in the picture to unlatch the plug (only possible if the switch had been set to position I)		# Use a small screwdriver and press as shown in the picture to unlatch the plug (only possible if the switch had been set to position I)
	# Unscrew the grub screw and remove without dropping it		# Unscrew the grub screw and remove without dropping it
	# If the ignition lock is removed the ignition switch can be ~~weaved~~ out		# If the ignition lock is removed the ignition switch can be left out
	<br/>		<br/>
	==== Assemble the ignition switch ====		==== Assemble the ignition switch ====
	# Use the (removed) ignition lock to ensure the switch is set to position I and the latch can be pressed in (see picture)		# Use the (removed) ignition lock to ensure the switch is set to position I and the latch can be pressed in (see picture)
	# ~~Weave~~ in the switch on the dowel and insert grub screw. Don't fully tighten ~~jet~~.		# Leave in the switch on the dowel and insert grub screw. Don't fully tighten yet.
	# Insert the ignition lock (see above)		# Insert the ignition lock (see above)
	# Tighten the grub screw		# Tighten the grub screw

Change the ignition switch - Revision history

Noisy Tim: /* S1 */

Eton at 08:44, 27 January 2014

Eton at 21:29, 26 January 2014

Eton at 21:29, 26 January 2014

Eton at 21:16, 26 January 2014

Stu at 20:45, 26 January 2014

Stu at 20:40, 26 January 2014

Eton at 16:37, 26 January 2014

Eton: Created page with "Categorie:Electrical Categorie:Elise S1 The ignition switch can wear which can cause malfunction (e.g. no starter). == S1 == The ingition switch used in th..."

Eton: Created page with "Categorie:Electrical Categorie:Elise S1 The ignition switch can wear which can cause malfunction (e.g. no starter).

== S1 == The ingition switch used in th..."