Fit a PRRT - Revision history

Liam: /* See Also */

2007-08-28T13:01:51Z

2007-08-28T12:56:21Z

2007-07-20T21:40:53Z

Parts Required and Suppliers

← Older revision		Revision as of 21:40, 20 July 2007
Line 15:		Line 15:

	1 off 32mm diameter x 50mm length alloy hose joiners (£5.00 each) - [http://www.midlandperformancecentre.co.uk/tuning/product.asp?cn=3005&scn=1052&scn2=2285&p=1955 Midland Performance Centre]		1 off 32mm diameter x 50mm length alloy hose joiners (£5.00 each) - [http://www.midlandperformancecentre.co.uk/tuning/product.asp?cn=3005&scn=1052&scn2=2285&p=1955 Midland Performance Centre]

	or cut a piece from the aluminium tube discarded from the original system		or cut a piece from the aluminium tube discarded from the original system

2007-07-20T21:40:36Z

Parts Required and Suppliers

← Older revision		Revision as of 21:40, 20 July 2007
Line 15:		Line 15:

	1 off 32mm diameter x 50mm length alloy hose joiners (£5.00 each) - [http://www.midlandperformancecentre.co.uk/tuning/product.asp?cn=3005&scn=1052&scn2=2285&p=1955 Midland Performance Centre]		1 off 32mm diameter x 50mm length alloy hose joiners (£5.00 each) - [http://www.midlandperformancecentre.co.uk/tuning/product.asp?cn=3005&scn=1052&scn2=2285&p=1955 Midland Performance Centre]
			or cut a piece from the aluminium tube discarded from the original system

	===How To Fit===		===How To Fit===

2007-04-20T19:55:36Z

← Older revision	Revision as of 19:55, 20 April 2007
(No difference)

2007-04-17T13:21:06Z

2007-03-12T12:54:05Z

← Older revision		Revision as of 12:54, 12 March 2007
Line 1:		Line 1:
	[[Category:Engine Cooling]]		[[Category:Engine Cooling]]
	[[Category:DIY]]		[[Category:DIY]]



Line 84:		Line 85:

	=== See Also ===		=== See Also ===

			'''There are several ways to set up your cooling system'''

			'''PLEASE ADD INFO'''
			<gallery>
			Image:robstevens.gif\|Rob Stevens Setup
			Image:stevebutts.gif\|Steve Butts Setup
			</gallery>


	http://wiki.seloc.org/a/PRT		http://wiki.seloc.org/a/PRT

2007-03-12T12:49:04Z

← Older revision		Revision as of 12:49, 12 March 2007
Line 35:		Line 35:
	*40 cm aluminium pipe, OD 32 mm ID 28 mm		*40 cm aluminium pipe, OD 32 mm ID 28 mm

	*8 l of coolant fluid (I used a red OAT product, as recommended by the manifacturer)		*8 lt of coolant fluid (I used a red OAT product, as recommended by the manifacturer)

	[[Image:LRstatSEC.jpg\|thumb\|left\|Click to Enlarge]]		[[Image:LRstatSEC.jpg\|thumb\|left\|Click to Enlarge]]

2007-03-12T12:47:56Z

← Older revision		Revision as of 12:47, 12 March 2007
Line 73:		Line 73:
	*Below there are some photos of the PRRT fitted to my car.		*Below there are some photos of the PRRT fitted to my car.

			<gallery>
			Image:ThermoF.jpg\|Click to Enlarge

	[[Image:~~ThermoF~~.jpg~~\|thumb\|left~~\|Click to Enlarge]]		Image:ThermoG.jpg\|Click to Enlarge
	~~{{clr}}~~

	~~[[Image:ThermoG.jpg\|thumb\|left\|Click to Enlarge]]~~		Image:ThermoH.jpg\|Click to Enlarge
	~~{{clr}}~~

	[[Image:ThermoH.jpg~~\|thumb\|left\|Click to Enlarge]]~~
	~~{{clr}}~~

	~~[[Image:ThermoL.jpg\|thumb\|left~~\|Click to Enlarge]]
	~~{{clr}}~~

			Image:ThermoL.jpg\|Click to Enlarge
			</gallery>

	=== See Also ===		=== See Also ===

	http://wiki.seloc.org/a/PRT		http://wiki.seloc.org/a/PRT

2007-03-12T12:45:40Z

@@ Line 57: / Line 57: @@
 This part is the most important of all: cutting the Kit hoses to make it fit. I prefer not to give measures about where you should cut the hoses because, on another car, the lengths required could be slightly different. you can take the photos as a guideline, but BE CAREFUL as, once you cut a hose too short, you are into trouble. My advice is to leave 2 cm extra hose as a safety margin, use no clips and then cut again where needed after having tried to make it fit. To achieve a clean rubber cut, you can insert the remaining of the aluminium tube where you need to do the cut. Hoses H and D need no cutting.
-Once reassembled, the PCH001190 kit should look like this:
+*Once reassembled, the PCH001190 kit should look like this:
 [[Image:EliseKit.jpg|thumb|left|Click to Enlarge]]
 {{clr}}

← Older revision		Revision as of 13:01, 28 August 2007
Line 92:		Line 92:
	'''PLEASE ADD INFO'''		'''PLEASE ADD INFO'''
	<gallery>		<gallery>
	Image:robstevens.gif\|Rob Stevens' Setup		Image:robstevens.gif\|Rob Stevens Setup
	Image:stevebutts.gif\|Steve ~~Butt's~~ Setup		Image:stevebutts.gif\|Steve Butts Setup
	Image:liamcrilly.gif\|Liam Crilly's Setup		Image:liamcrilly.gif\|Liam Crilly's Setup
	</gallery>		</gallery>

← Older revision		Revision as of 12:56, 28 August 2007
Line 92:		Line 92:
	'''PLEASE ADD INFO'''		'''PLEASE ADD INFO'''
	<gallery>		<gallery>
	Image:robstevens.gif\|Rob Stevens Setup		Image:robstevens.gif\|Rob Stevens' Setup
	Image:stevebutts.gif\|Steve ~~Butts~~ Setup		Image:stevebutts.gif\|Steve Butt's Setup
			Image:liamcrilly.gif\|Liam Crilly's Setup
	</gallery>		</gallery>