Fit a front splitter - Revision history

will111s: /* Bolts */

2009-01-14T18:30:38Z

Bolts

@@ Line 10: / Line 10: @@
 === Bolts ===
-/25mm spreader washers
+This description was written for fitting one of Tigga's splitters, but could be applied to other splitters as well
 == Incorrect fitment ==

2007-04-20T19:48:41Z

← Older revision	Revision as of 19:48, 20 April 2007
(No difference)

2007-04-17T13:23:17Z

2006-09-11T21:58:49Z

Bolts

2006-09-11T19:43:01Z

← Older revision		Revision as of 19:43, 11 September 2006
Line 11:		Line 11:
	=== Bolts ===		=== Bolts ===

	== ~~Damage~~ ==		== Incorrect fitment ==
	[[Image:how to fit a front slitter - incorrectly fitted.jpg\|thumb\|left\|Make sure you use large spreader washers]]		[[Image:how to fit a front slitter - incorrectly fitted.jpg\|thumb\|left\|Make sure you use large spreader washers]]
	Unfortunately, if not correctly fitted, the splitter can part company with your car at high speeds. At best this will damage the splitter, at worse, your front clamshell. Remember it needs to sustain around 40 Kg of down force.		Unfortunately, if not correctly fitted, the splitter can part company with your car at high speeds. At best this will damage the splitter, at worse, your front clamshell. Remember it needs to sustain around 40 Kg of down force.

2006-09-11T19:32:10Z

← Older revision		Revision as of 19:32, 11 September 2006
Line 18:		Line 18:
	== Removal ==		== Removal ==
	If you want to remove the splitter you can use a sharp (Stanley) blade to cut the ''seal'' and it comes off relatively easily.		If you want to remove the splitter you can use a sharp (Stanley) blade to cut the ''seal'' and it comes off relatively easily.

	~~== Procurement ==~~
	~~Fellow SELOC member [http://forums.seloc.org/member.php?action=viewpro&member=Tigga%21 Tigga!] supplies a splitter for the Elise S2.~~

	[[Category:Aerodynamics]]		[[Category:Aerodynamics]]
	[[Category:DIY]]		[[Category:DIY]]

2006-09-11T19:25:59Z

Damage

← Older revision		Revision as of 19:25, 11 September 2006
Line 13:		Line 13:
	== Damage ==		== Damage ==
	[[Image:how to fit a front slitter - incorrectly fitted.jpg\|thumb\|left\|Make sure you use large spreader washers]]		[[Image:how to fit a front slitter - incorrectly fitted.jpg\|thumb\|left\|Make sure you use large spreader washers]]
	Unfortunately, if not correctly fitted, the splitter can damage the front clamshell ~~when it parts company to high speeds~~. Remember it needs to sustain around 40 Kg of down force.		Unfortunately, if not correctly fitted, the splitter can part company with your car at high speeds. At best this will damage the splitter, at worse, your front clamshell. Remember it needs to sustain around 40 Kg of down force.
	{{clr}}		{{clr}}

2006-09-11T19:22:42Z

← Older revision		Revision as of 19:22, 11 September 2006
Line 10:		Line 10:

	=== Bolts ===		=== Bolts ===

			== Damage ==
			[[Image:how to fit a front slitter - incorrectly fitted.jpg\|thumb\|left\|Make sure you use large spreader washers]]
			Unfortunately, if not correctly fitted, the splitter can damage the front clamshell when it parts company to high speeds. Remember it needs to sustain around 40 Kg of down force.
			{{clr}}

	== Removal ==		== Removal ==

2006-09-11T19:03:36Z

Procedure

← Older revision		Revision as of 19:03, 11 September 2006
Line 4:		Line 4:

	== Procedure ==		== Procedure ==
			There are two ways to secure the splitter to the front clamshell.

			=== Glue ===
	* Sikaflex		* Sikaflex

			=== Bolts ===

	== Removal ==		== Removal ==

2006-09-11T19:01:00Z

← Older revision		Revision as of 19:01, 11 September 2006
Line 1:		Line 1:
	[[Image:~~Front~~ splitter.jpg\|thumb\|left\|~~Splitter fitted to front of Elise S2~~]]		[[Image:How to fit a front splitter.jpg\|thumb\|left\|Front splitter]]
	Fitting a [[front splitter]] to the front of your car couldn't be easier.		Fitting a [[front splitter]] to the front of your car couldn't be easier.
	{{clr}}		{{clr}}

	== Procedure ==		== Procedure ==
	# Sikaflex		* Sikaflex

	== Removal ==		== Removal ==
Line 12:		Line 12:
	Fellow SELOC member [http://forums.seloc.org/member.php?action=viewpro&member=Tigga%21 Tigga!] supplies a splitter for the Elise S2.		Fellow SELOC member [http://forums.seloc.org/member.php?action=viewpro&member=Tigga%21 Tigga!] supplies a splitter for the Elise S2.

			[[Category:Aerodynamics]]
	[[Category:DIY]]		[[Category:DIY]]