Smaller Rear View Mirror - Revision history

JohnF: /* Golf 2 mirror */

2014-09-09T08:46:45Z

Golf 2 mirror

← Older revision		Revision as of 08:46, 9 September 2014
Line 58:		Line 58:

	Or, pop out old mirror (mine came out without any bother), then use sandpaper on the ball of the new VW mirror till you have made the ball small enough to pop in without smashing your windscreen. Only took a few minutes of rubbing to get it to fit. Ohhh la.		Or, pop out old mirror (mine came out without any bother), then use sandpaper on the ball of the new VW mirror till you have made the ball small enough to pop in without smashing your windscreen. Only took a few minutes of rubbing to get it to fit. Ohhh la.

			Added by JohnF

			Initially, I couldn't get the Golf mirror to fit, even with a bit of WD40. I wasn't keen on sanding the ball down, in case this left it too loose and I was half way back to where I started (i.e. mirror ending up lopsided after 5 minutes drive). I eventually put a towel round the mirror, put the mirror onto a bench, positioned the ball onto the socket and gave the socket mount a sharp hit with hammer. It popped in first time. Obviously, I can't guarantee that this will work again - I did it having reached a point where I figured if it wouldn't go in I was happy to sacrifice a 2nd hand Golf mirror.

	== Child view mirrors ==		== Child view mirrors ==

Lewtus: /* Golf 2 mirror */

2013-08-12T17:01:43Z

Golf 2 mirror

← Older revision		Revision as of 17:01, 12 August 2013
Line 56:		Line 56:

	Done!		Done!

			Or, pop out old mirror (mine came out without any bother), then use sandpaper on the ball of the new VW mirror till you have made the ball small enough to pop in without smashing your windscreen. Only took a few minutes of rubbing to get it to fit. Ohhh la.

	== Child view mirrors ==		== Child view mirrors ==

Daviesje at 08:07, 19 January 2013

2013-01-19T08:07:33Z

← Older revision		Revision as of 08:07, 19 January 2013
Line 20:		Line 20:
	# Remove the mirror from the stalk by popping the "ball and socket" joint out of joint, - just angle it too far in any direction forcably.		# Remove the mirror from the stalk by popping the "ball and socket" joint out of joint, - just angle it too far in any direction forcably.
	# Find a Daewoo Matiz in a scrappy. - don't bother trying to remove the stalk and all from the windscreen (i couldn't manage), just dislocate the ball and socket joint in the same way. Just take the mirror leaving the stalk behind.		# Find a Daewoo Matiz in a scrappy. - don't bother trying to remove the stalk and all from the windscreen (i couldn't manage), just dislocate the ball and socket joint in the same way. Just take the mirror leaving the stalk behind.
	# Put the new mirror face down on something soft like your seat, put the ball on the end of your Lotus stalk into the socket of the Daewoo mirror and shove downwards HARD ~~untill~~ it clicks into place.		# Put the new mirror face down on something soft like your seat, put the ball on the end of your Lotus stalk into the socket of the Daewoo mirror and shove downwards HARD until it clicks into place. If this proves tough to do, place the arm with the ball-end in your freezer overnight, and the mirror assembly in a warm place (on a radiator worked for me). The small shrinkage in ball, and small expansion & softening of socket makes the operation a bit easier.
	# Slide the whole thing back onto the windscreen mounting.		# Slide the whole thing back onto the windscreen mounting.

Friso: /* Golf 2 mirror */

2012-06-08T20:55:27Z

Golf 2 mirror

← Older revision		Revision as of 20:55, 8 June 2012
Line 52:		Line 52:
	# Remove the mirror from the stalk by popping the "ball and socket" joint out of joint. I'd say lubricate it and pull straight out. (I don't know for certain, because my mirror just fell off its stalk.)		# Remove the mirror from the stalk by popping the "ball and socket" joint out of joint. I'd say lubricate it and pull straight out. (I don't know for certain, because my mirror just fell off its stalk.)
	# Find a small mirror with it's ball joint on top in a scrappy. In my case I found a Golf 2 with a nice small mirror. I removed the stalk and mirror and separated them at home, using some WD40. I pulled straight out.		# Find a small mirror with it's ball joint on top in a scrappy. In my case I found a Golf 2 with a nice small mirror. I removed the stalk and mirror and separated them at home, using some WD40. I pulled straight out.
	# Push the old stalk in the new mirror. I checked the size of both joints first. I'd say most of these joints are roughly the same size, but better safe than sorry.		# Push the old stalk in the new mirror using some lubricant like WD40 I checked the size of both joints first. I'd say most of these joints are roughly the same size, but better safe than sorry.
	# Slide the whole thing back onto the windscreen mounting.		# Slide the whole thing back onto the windscreen mounting.

Friso: /* Golf 2 mirror */

2012-06-08T20:54:00Z

Golf 2 mirror

← Older revision		Revision as of 20:54, 8 June 2012
Line 40:		Line 40:
	At least my 2004 S2 111S had a GM mirror with the ball joint on top of the mirror. It is a whopping 260mm wide...		At least my 2004 S2 111S had a GM mirror with the ball joint on top of the mirror. It is a whopping 260mm wide...

	Anyway: I've found a Golf 2 mirror to fit quite nicely. This mirror is even smaller than a Deawoo Matiz mirror and, more importantly, it fits on cars that have mirrors which have their ball joint on top.		Anyway: I've found a Golf 2 mirror (part no. E1 0010012) to fit quite nicely. This mirror is even smaller than a Deawoo Matiz mirror and, more importantly, it fits on cars that have mirrors which have their ball joint on top.

	<gallery>		<gallery>

Nigelhannam at 21:10, 15 April 2012

2012-04-15T21:10:10Z

← Older revision		Revision as of 21:10, 15 April 2012
Line 32:		Line 32:

	The "big" OEM mirrors are ~235mm wide at widest point, the "small" OEM mirrors are about 205mm - measure yours first before you go rooting about in a scrap yard!		The "big" OEM mirrors are ~235mm wide at widest point, the "small" OEM mirrors are about 205mm - measure yours first before you go rooting about in a scrap yard!

			The Matiz mirror mount that I picked up from a scrappy was attached with a grub screw similar to the OEM Elise mount. It fits directly onto the 'lozenge' on the S1 windscreen and leaves the mirror around the same position as the OEM mount in its lowest position. If you normally move the OEM mirror to it's highest position you'll find that the Matiz mount leaves it obscuring the view through the windscreen a little, but it's another option you don't want to split the mirror ball/socket.

	== Golf 2 mirror ==		== Golf 2 mirror ==

Friso: /* Golf 2 mirror */

2012-03-29T18:30:24Z

Golf 2 mirror

← Older revision		Revision as of 18:30, 29 March 2012
Line 36:		Line 36:
	Addition by Friso:		Addition by Friso:
	There is some confusion about which kind of mirror is fitted to which cars, I suppose...		There is some confusion about which kind of mirror is fitted to which cars, I suppose...
	At least my 2004 S2 111S had a GM mirror with the ball joint on top of the mirror.		At least my 2004 S2 111S had a GM mirror with the ball joint on top of the mirror. It is a whopping 260mm wide...

	Anyway: I've found a Golf 2 mirror to fit quite nicely. This mirror is even smaller than a Deawoo Matiz mirror and, more importantly, it fits on cars that have mirrors which have their ball joint on top.		Anyway: I've found a Golf 2 mirror to fit quite nicely. This mirror is even smaller than a Deawoo Matiz mirror and, more importantly, it fits on cars that have mirrors which have their ball joint on top.

Paulc at 20:23, 28 March 2012

2012-03-28T20:23:04Z

@@ Line 1: / Line 1: @@
 If you drive a lot of twisty country roads you may have found that the JUMBO sized OEM rear view mirror gets in the way, obscuring a lot of the view out of the windscreen.
-==Daewoo mirror==
+__TOC__
 [[Image:daewoomatiz.jpg|thumb|100px|right|Daewoo Matiz]] A cheap alternative is to fit the mirror from a daewoo matiz (funny wee 3 cylinder shopping trolly, i'd guess most big scrappys would have a few crashed ones. - my local breaker in Glasgow had 5 today.
@@ Line 31: / Line 33: @@
 The "big" OEM mirrors are ~235mm wide at widest point, the "small" OEM mirrors are about 205mm - measure yours first before you go rooting about in a scrap yard!
 == Golf 2 mirror ==
 Addition by Friso:
 There is some confusion about which kind of mirror is fitted to which cars, I suppose...
@@ Line 65: / Line 55: @@
 Done!
 [[Category:DIY]]

Paulc: /* Daewoo mirror */

2012-03-28T20:19:58Z

Daewoo mirror

← Older revision		Revision as of 20:19, 28 March 2012
Line 15:		Line 15:
	Instructions :		Instructions :

	~~1 - remove~~ lotus mirror, by sliding the whole thing (including its stalk) upwards towards the top of the windscreen. - it just slides up leaving a small flat mounting plate in place on the windscreen.		# Remove lotus mirror, by sliding the whole thing (including its stalk) upwards towards the top of the windscreen. - it just slides up leaving a small flat mounting plate in place on the windscreen.
			# Remove the mirror from the stalk by popping the "ball and socket" joint out of joint, - just angle it too far in any direction forcably.
	~~2 - remove~~ the mirror from the stalk by popping the "ball and socket" joint out of joint, - just angle it too far in any direction forcably.		# Find a Daewoo Matiz in a scrappy. - don't bother trying to remove the stalk and all from the windscreen (i couldn't manage), just dislocate the ball and socket joint in the same way. Just take the mirror leaving the stalk behind.
			# Put the new mirror face down on something soft like your seat, put the ball on the end of your Lotus stalk into the socket of the Daewoo mirror and shove downwards HARD untill it clicks into place.
	~~3 - find~~ a Daewoo Matiz in a scrappy. - don't bother trying to remove the stalk and all from the windscreen (i couldn't manage), just dislocate the ball and socket joint in the same way. Just take the mirror leaving the stalk behind.		# Slide the whole thing back onto the windscreen mounting.

	~~4 - put~~ the new mirror face down on something soft like your seat, put the ball on the end of your Lotus stalk into the socket of the Daewoo mirror and shove downwards HARD untill it clicks into place.

	~~5 - slide~~ the whole thing back onto the windscreen mounting.

	Bingo!		Bingo!

Paulc: inline images rather than thread link

2012-03-28T20:16:47Z

inline images rather than thread link

← Older revision		Revision as of 20:16, 28 March 2012
Line 52:		Line 52:
	At least my 2004 S2 111S had a GM mirror with the ball joint on top of the mirror.		At least my 2004 S2 111S had a GM mirror with the ball joint on top of the mirror.

	Anyway: I've found a Golf 2 mirror to fit quite nicely. This mirror is even smaller than a Deawoo Matiz mirror and, more importantly, it fits on cars that have mirrors which have their ball joint on top. ~~Pictures are in this thread~~: ~~http~~:~~//forums~~.~~seloc~~.~~org~~/~~viewthread.php?tid=333057~~		Anyway: I've found a Golf 2 mirror to fit quite nicely. This mirror is even smaller than a Deawoo Matiz mirror and, more importantly, it fits on cars that have mirrors which have their ball joint on top.

			<gallery>
			Image:VW_compare.jpg\|GM and VW comparison.
			Image:VW_in_situ.jpg\|VW mirror in-situ.
			</gallery>

	Instructions:		Instructions:

	~~1 - remove~~ lotus mirror, by sliding the whole thing (including its stalk) DOWNWARDS. - it just slides ~~downl~~ leaving a small mounting plate in place on the windscreen.		# Remove lotus mirror, by sliding the whole thing (including its stalk) DOWNWARDS. - it just slides down leaving a small mounting plate in place on the windscreen.
			# Remove the mirror from the stalk by popping the "ball and socket" joint out of joint. I'd say lubricate it and pull straight out. (I don't know for certain, because my mirror just fell off its stalk.)
	~~2 - remove~~ the mirror from the stalk by popping the "ball and socket" joint out of joint. I'd say lubricate it and pull straight out. (I don't know for certain, because my mirror just fell off its stalk.)		# Find a small mirror with it's ball joint on top in a scrappy. In my case I found a Golf 2 with a nice small mirror. I removed the stalk and mirror and separated them at home, using some WD40. I pulled straight out.
			# Push the old stalk in the new mirror. I checked the size of both joints first. I'd say most of these joints are roughly the same size, but better safe than sorry.
	~~3 - find~~ a small mirror with it's ball joint on top in a scrappy. In my case I found a Golf 2 with a nice small mirror. I removed the stalk and mirror and separated them at home, using some WD40. I pulled straight out.		# Slide the whole thing back onto the windscreen mounting.

	~~4 - push~~ the old stalk in the new mirror. I checked the size of both joints first. I'd say most of these joints are roughly the same size, but better safe than sorry.

	~~5 - slide~~ the whole thing back onto the windscreen mounting.

	Done!		Done!