Difference between revisions of "Remove the gear knob"
Mccarefree (talk | contribs) m (→Rover Engine: Grip + protection!) |
|||
| (2 intermediate revisions by one other user not shown) | |||
| Line 25: | Line 25: | ||
Enter procedure here. | Enter procedure here. | ||
| + | |||
| + | Elise S1 | ||
I used a Softgrip strap wrench (http://www.ccw-tools.com/product.asp?P_ID=23331&gclid=CIqZxOKH0rYCFerHtAodzFwAUw) about £14 but it did not budge. | I used a Softgrip strap wrench (http://www.ccw-tools.com/product.asp?P_ID=23331&gclid=CIqZxOKH0rYCFerHtAodzFwAUw) about £14 but it did not budge. | ||
| Line 33: | Line 35: | ||
2. Wrapped that around the knob. | 2. Wrapped that around the knob. | ||
| + | |||
3. Put the wrench tight over the folded wet and dry (sandpaper surface on the knob and rubber of the strap) | 3. Put the wrench tight over the folded wet and dry (sandpaper surface on the knob and rubber of the strap) | ||
| + | |||
4. A good yank and it moved very easily. | 4. A good yank and it moved very easily. | ||
| − | 5. Off with the knob, slight scratches to the knob | + | |
| + | 5. Off with the knob, slight surface scratches to the knob, no deep marks. | ||
| + | |||
6. On goes the woolen knob warmer for a few hundred miles that will polish them out. | 6. On goes the woolen knob warmer for a few hundred miles that will polish them out. | ||
| + | I used a short length of old mountain bike inner tube folded back on itself for double thickness and pulled down condom style. Wound the knob off with a chain wrench (it was v tight starting). Lots of grip and no damage to the knob. Not so good for the inner tube.... | ||
[[Category:DIY]] | [[Category:DIY]] | ||
Latest revision as of 11:25, 21 October 2016
Toyota Engine
Lotus stick their gear knobs on with Loctite, or something similar, as they are pretty diffucult to get off. Brute force is normally needed, but it does help to know which way to turn it. On my 111R it was very, VERY difficult to turn. Obviously the longer the bar/allen key you use, the more leverage you get, and you need a lot!
Required tools:
- 2.5mm Allen Key
- Larger Allen Key / bar to fit in grub hole (for leverage)
- Beer
1. Using a 2.5mm allen key, remove the grub screw on the front side (the side closest to "R, 1st, 3rd & 5th").
2. Get prepared for swearing, grunting, anger.
3. Using a larger allen key, or similar size 'bar' for extra leverage in the grub screw hold, turn the knob anti-clockwise (as looking from the top).
4. Once removed, reward oneself with beer.
5. Do what you wanted to do with the knob: clean it, polish it, put a new gear gaiter on etc.
6. Replace knob in the opposite fashion to which you removed it.
Rover Engine
Enter procedure here.
Elise S1
I used a Softgrip strap wrench (http://www.ccw-tools.com/product.asp?P_ID=23331&gclid=CIqZxOKH0rYCFerHtAodzFwAUw) about £14 but it did not budge.
After rubbing of my head:
1. Cut a piece of wet and dry 600 3 inches width of the sheet.
2. Wrapped that around the knob.
3. Put the wrench tight over the folded wet and dry (sandpaper surface on the knob and rubber of the strap)
4. A good yank and it moved very easily.
5. Off with the knob, slight surface scratches to the knob, no deep marks.
6. On goes the woolen knob warmer for a few hundred miles that will polish them out.
I used a short length of old mountain bike inner tube folded back on itself for double thickness and pulled down condom style. Wound the knob off with a chain wrench (it was v tight starting). Lots of grip and no damage to the knob. Not so good for the inner tube....