Difference between revisions of "Change the ignition switch"
Jump to navigation
Jump to search
(→S1) |
|||
| (3 intermediate revisions by one other user not shown) | |||
| Line 6: | Line 6: | ||
The ignition switch used in the Elise S1 is like the rest of the steering column from GM/Vauxhall/Opel (e.g. Corsa B). The GM spare part number is 914852 or 90389377.<br/> | The ignition switch used in the Elise S1 is like the rest of the steering column from GM/Vauxhall/Opel (e.g. Corsa B). The GM spare part number is 914852 or 90389377.<br/> | ||
<br/> | <br/> | ||
| − | '''IMPORTANT!!! To remove/insert the ignition lock and/or switch ensure the key is inserted and is set to position I''' (key vertical and position where normally the radio is on but ignition is still off).<br/> | + | '''IMPORTANT!!! To remove/insert the ignition lock and/or switch ensure the key is inserted and is set to position I''' (key vertical and position where normally the radio is on but ignition is still off). On a 2004 111S, (and probably other years and models too), it has to be in position 2.<br/> |
<br/> | <br/> | ||
=== Ignition lock === | === Ignition lock === | ||
| Line 13: | Line 13: | ||
# Remove the column shroud (7 screws and 1 nut for the trip switch) | # Remove the column shroud (7 screws and 1 nut for the trip switch) | ||
# Insert key and set to position I (key must be vertical - see picture) | # Insert key and set to position I (key must be vertical - see picture) | ||
| − | # At the front side (the side where the steering wheel is) of the outer barrel is a small hole. Press the short side of a small allen key into the hole (see picture). At the same time press the lock | + | # At the front side (the side where the steering wheel is) of the outer barrel is a small hole. Press the short side of a small allen key into the hole (see picture). At the same time press the lock by the key towards the column and gently wiggle the lock until is comes loose. The lock is pressed out by spring tension. |
<br/> | <br/> | ||
==== Insert the ignition lock ==== | ==== Insert the ignition lock ==== | ||
| Line 26: | Line 26: | ||
==== Remove the ignition switch ==== | ==== Remove the ignition switch ==== | ||
[[File:Zuend_2.jpg|right|thumb|240px|Direction to unlock the ignition switch]] | [[File:Zuend_2.jpg|right|thumb|240px|Direction to unlock the ignition switch]] | ||
| − | [[File:Zuendschalter.jpg|right|thumb|240px|Direction to | + | [[File:Zuendschalter.jpg|right|thumb|240px|Direction to unlatch the plug]] |
[[File:Zuend_3.jpg|right|thumb|240px|Unscrew the ignition switch fix grub screw]] | [[File:Zuend_3.jpg|right|thumb|240px|Unscrew the ignition switch fix grub screw]] | ||
# Disconnect the battery | # Disconnect the battery | ||
# Remove the ignition lock (see above) | # Remove the ignition lock (see above) | ||
# Use a small screwdriver to remove the ignition switch cover or unlock switch with the cover mounted (more fiddly but possible - see picture) | # Use a small screwdriver to remove the ignition switch cover or unlock switch with the cover mounted (more fiddly but possible - see picture) | ||
| − | # Use a small screwdriver and press as shown in the picture to unlatch the plug (only possible if the switch had been set to position I) | + | # Use a small screwdriver and press as shown in the picture to unlatch the plug (only possible if the switch had been set to position I) and disconnect the plug |
# Unscrew the grub screw and remove without dropping it | # Unscrew the grub screw and remove without dropping it | ||
| − | # | + | # The switch is now only held by a small dowel. Move the switch towards the steering wheel to get it off the dowel and remove it. |
<br/> | <br/> | ||
==== Assemble the ignition switch ==== | ==== Assemble the ignition switch ==== | ||
# Use the (removed) ignition lock to ensure the switch is set to position I and the latch can be pressed in (see picture) | # Use the (removed) ignition lock to ensure the switch is set to position I and the latch can be pressed in (see picture) | ||
| − | # Insert in the switch on the dowel and screw in grub screw. Don't fully tighten yet. | + | # Insert in the switch on the dowel and screw in the grub screw. Don't fully tighten yet. |
# Insert the ignition lock (see above) | # Insert the ignition lock (see above) | ||
# Tighten the grub screw | # Tighten the grub screw | ||
Latest revision as of 07:34, 7 April 2024
The ignition switch can wear which can cause malfunction (e.g. no starter).
S1
The ignition switch used in the Elise S1 is like the rest of the steering column from GM/Vauxhall/Opel (e.g. Corsa B). The GM spare part number is 914852 or 90389377.
IMPORTANT!!! To remove/insert the ignition lock and/or switch ensure the key is inserted and is set to position I (key vertical and position where normally the radio is on but ignition is still off). On a 2004 111S, (and probably other years and models too), it has to be in position 2.
Ignition lock
Remove the ignition lock
- Remove the column shroud (7 screws and 1 nut for the trip switch)
- Insert key and set to position I (key must be vertical - see picture)
- At the front side (the side where the steering wheel is) of the outer barrel is a small hole. Press the short side of a small allen key into the hole (see picture). At the same time press the lock by the key towards the column and gently wiggle the lock until is comes loose. The lock is pressed out by spring tension.
Insert the ignition lock
- Before inserting the ignition lock make sure the steering wheel lock is disengaged. Use a small screwdriver to push the mechanism downwards until it locks into place (see picture)
- Ensure the key is inserted and is set to position I. Test if the locking notch on top of the ignition lock can be pressed in until it is level with the outer shape of the lock.
- Press the lock into the barrel until it locks into place
- Check function and reattach the shroud
Ignition switch
Remove the ignition switch
- Disconnect the battery
- Remove the ignition lock (see above)
- Use a small screwdriver to remove the ignition switch cover or unlock switch with the cover mounted (more fiddly but possible - see picture)
- Use a small screwdriver and press as shown in the picture to unlatch the plug (only possible if the switch had been set to position I) and disconnect the plug
- Unscrew the grub screw and remove without dropping it
- The switch is now only held by a small dowel. Move the switch towards the steering wheel to get it off the dowel and remove it.
Assemble the ignition switch
- Use the (removed) ignition lock to ensure the switch is set to position I and the latch can be pressed in (see picture)
- Insert in the switch on the dowel and screw in the grub screw. Don't fully tighten yet.
- Insert the ignition lock (see above)
- Tighten the grub screw
- If you removed the cover of the plug reattach it
- Press the plug in the switch until it latches
- Reconnect the battery and test switch
- Reattach the shroud