Difference between revisions of "Head gasket failure"
m |
|||
(5 intermediate revisions by 4 users not shown) | |||
Line 6: | Line 6: | ||
{{clr}} | {{clr}} | ||
− | == Symptoms == | + | === Symptoms === |
Signs of HGF tend to include oil in the [[coolant]] expansion bottle, or [[Engine oil |oil]] becoming emulsified where the coolant from the coolant ways seeps through the gasket into oil. This can normally be seen as a ''[http://en.wikipedia.org/wiki/Mayonnaise mayonnaise]'' like substance inside the oil filler cap or the engine oil dipstick. | Signs of HGF tend to include oil in the [[coolant]] expansion bottle, or [[Engine oil |oil]] becoming emulsified where the coolant from the coolant ways seeps through the gasket into oil. This can normally be seen as a ''[http://en.wikipedia.org/wiki/Mayonnaise mayonnaise]'' like substance inside the oil filler cap or the engine oil dipstick. | ||
Line 19: | Line 19: | ||
=== Handling === | === Handling === | ||
If you suspect HGF, '''do not''' drive the car and have it checked by a reputable garage. This can include checking the coolant for hydrocarbons to see if oil/gases have escaped past the gasket into the coolant ways. If the engine has overheated and the cylinder head has become warped, then the head will need to be skimmed so that it can be reseated onto a new gasket at a later date. | If you suspect HGF, '''do not''' drive the car and have it checked by a reputable garage. This can include checking the coolant for hydrocarbons to see if oil/gases have escaped past the gasket into the coolant ways. If the engine has overheated and the cylinder head has become warped, then the head will need to be skimmed so that it can be reseated onto a new gasket at a later date. | ||
+ | |||
+ | |||
+ | There is plenty of information about HG repalcement here, but a few points to note if you want it to last | ||
+ | |||
+ | i) the head should be hardness tested and be more than 95 Brinell | ||
+ | |||
+ | ii) the head should be peened on the fire ring area to eradicate porosity followed by a skim | ||
+ | |||
+ | iii) the liner heights should be checked and if they are lower then 4 thou they should be corrected | ||
+ | |||
+ | iv) a Payen BW750 gasket or if you must an MLS Payen BW5750 gasket should be used. | ||
+ | |||
+ | Get these right and the fix will last. | ||
=== Treatment === | === Treatment === | ||
Line 24: | Line 37: | ||
Fit new head gasket. | Fit new head gasket. | ||
− | == Precautions == | + | === Precautions === |
Certain precautions can be taken to help alleviate the problem of HGF. These include | Certain precautions can be taken to help alleviate the problem of HGF. These include | ||
* Always check the coolant level. | * Always check the coolant level. | ||
Line 31: | Line 44: | ||
* Fit a [[remote stat]]. | * Fit a [[remote stat]]. | ||
* Upgrade the [http://en.wikipedia.org/wiki/Head_gasket head gasket]. | * Upgrade the [http://en.wikipedia.org/wiki/Head_gasket head gasket]. | ||
+ | * Install the new type oil ladder combined with the multi layer head gasket | ||
− | + | === HGF Pictures === | |
− | == HGF Pictures == | ||
<gallery> | <gallery> | ||
Image:Spunky.jpg|Oil in coolant, no other signs of failure | Image:Spunky.jpg|Oil in coolant, no other signs of failure | ||
Image:Spunky1.jpg|Oil in coolant, no other signs of failure | Image:Spunky1.jpg|Oil in coolant, no other signs of failure | ||
− | Image:spunky2.JPG| | + | Image:spunky2.JPG|Mayonnaise type substance in coolant tank |
− | Image:spunky3.JPG| | + | Image:spunky3.JPG|Mayonnaise type substance on the oil filler cap |
− | |||
− | |||
</gallery> | </gallery> | ||
Latest revision as of 21:37, 13 March 2014
Head Gasket Failure, or HGF, is all too common on the Rover ‘K’ series engine. What happens is the head gasket, which sits between the engine block and cylinder head, fails, allowing pathways between the firing area and cooling system to form. A more detailed explanation can be found here.
Original designs of the were held in place by dowels that allowed minute movement of the gasket. Later gaskets are held in place by steel dowels, which do not allow movement of the gasket.
Symptoms
Signs of HGF tend to include oil in the coolant expansion bottle, or oil becoming emulsified where the coolant from the coolant ways seeps through the gasket into oil. This can normally be seen as a mayonnaise like substance inside the oil filler cap or the engine oil dipstick.
- Oil in coolant expansion bottle.
- Brown layer of foam floating on the coolant.
- Mayonnaise type substance on the oil filler cap/dipstick.
- Steam from the exhaust pipe.
- Erratic temp readings on the stack display.
- Blown radiator.
Handling
If you suspect HGF, do not drive the car and have it checked by a reputable garage. This can include checking the coolant for hydrocarbons to see if oil/gases have escaped past the gasket into the coolant ways. If the engine has overheated and the cylinder head has become warped, then the head will need to be skimmed so that it can be reseated onto a new gasket at a later date.
There is plenty of information about HG repalcement here, but a few points to note if you want it to last
i) the head should be hardness tested and be more than 95 Brinell
ii) the head should be peened on the fire ring area to eradicate porosity followed by a skim
iii) the liner heights should be checked and if they are lower then 4 thou they should be corrected
iv) a Payen BW750 gasket or if you must an MLS Payen BW5750 gasket should be used.
Get these right and the fix will last.
Treatment
Does the head need skimming? Fit new head gasket.
Precautions
Certain precautions can be taken to help alleviate the problem of HGF. These include
- Always check the coolant level.
- Hoses for damage and jubilee clips for tightness.
- Warming the engine up gradually from cold may also be beneficial.
- Fit a remote stat.
- Upgrade the head gasket.
- Install the new type oil ladder combined with the multi layer head gasket
HGF Pictures