Difference between revisions of "How to remove badges"
m |
m |
||
| Line 9: | Line 9: | ||
{{clr}} | {{clr}} | ||
| − | + | Options to loosen the badge include heat (hairdryers, hot water, heat guns)and simply prying the badge off, but these do run the risk of damage to your paintwork in some cases. | |
| − | + | However, one thing that does work without any chance of damage (assuming your car is clean and there's no grit/dirt to grind into the paint) is the fishing line/dental floss technique. | |
| − | |||
| − | However, one thing that does work without any chance of damage is the fishing line/dental floss technique. | ||
[[image:badge2.jpg]] | [[image:badge2.jpg]] | ||
{{clr}} | {{clr}} | ||
| − | Lotus have kindly considered this technique when they were designing the build quality of their cars. They left a small gap all the way around the badge through which you can pull taught a length of nylon fishing line. | + | Lotus have kindly considered this technique when they were designing the build quality of their cars. They left a small gap all the way around the badge through which you can pull taught a length of nylon fishing line or dental floss. |
| − | With a sawing action back and forth, the line will easily cut through the | + | With a sawing action back and forth, the line/floss will easily cut through the adhesive pad holding the badge to the clam. The line (and particularly floss) may snap a few times but it's cheap so just grab another bit! Work slowly though and without any bling rings on your hand and there'll be no risk to your paint work. |
[[image:badge3.jpg]] | [[image:badge3.jpg]] | ||
| Line 30: | Line 28: | ||
{{clr}} | {{clr}} | ||
| − | Next you have to remove the | + | Next you have to remove the adhesive pad. The best method for this is pulling at it gently, as it stretches and comes away in clumps. Failing this, you'll need to rub away at it with a finger or thumb nail. Tar Remover etc can be used if needs be but physical persuasion will be required. |
[[image:badge5.jpg]] | [[image:badge5.jpg]] | ||
{{clr}} | {{clr}} | ||
| − | Once the | + | Once the adhesive pad is all gone, all you are left with is a bit of sticky glue on your car. This is best removed with a bit of Meths or tar remover etc. |
Revision as of 15:13, 28 March 2007
How to remove badges
Screw in type
Stuck on type
Options to loosen the badge include heat (hairdryers, hot water, heat guns)and simply prying the badge off, but these do run the risk of damage to your paintwork in some cases.
However, one thing that does work without any chance of damage (assuming your car is clean and there's no grit/dirt to grind into the paint) is the fishing line/dental floss technique.
Lotus have kindly considered this technique when they were designing the build quality of their cars. They left a small gap all the way around the badge through which you can pull taught a length of nylon fishing line or dental floss.
With a sawing action back and forth, the line/floss will easily cut through the adhesive pad holding the badge to the clam. The line (and particularly floss) may snap a few times but it's cheap so just grab another bit! Work slowly though and without any bling rings on your hand and there'll be no risk to your paint work.
Eventually, you'll be through and the plastic faded badge will fall to the ground.
Next you have to remove the adhesive pad. The best method for this is pulling at it gently, as it stretches and comes away in clumps. Failing this, you'll need to rub away at it with a finger or thumb nail. Tar Remover etc can be used if needs be but physical persuasion will be required.
Once the adhesive pad is all gone, all you are left with is a bit of sticky glue on your car. This is best removed with a bit of Meths or tar remover etc.