Radiator

Standard OEM radiator with plastic end tanks

The standard OEM Elise radiator is another weak point in the cooling system. Although it is lightweight, it has plastic end tanks which are prone to expanding and leaking under pressure.

Unfortunately you need to Remove S2 front clamshell before you can replace the radiator.

A upgraded radiator is pretty advisable when going for Honda/Audi/Duratec engine upgrades. Most converted cars on the original radiators seem to blow them up pretty soon after conversion.

Leaks

Drivers side end tank leaking under pressure

The most common fault with the OEM radiator is cracking/spliting of the plastic end tanks. The first signs of failure are drops of coolent on the windscreen, either drivers or passengers side, but castrophic failure of the end tanks has been known.

Quite often the passenger side hose is poorly connected (because it is difficult to do) and sometimes the bleed screw can leak.

The OEM radiators seem to have a problem with their manufacture where the main core is bonded to the top/bottom and leaks are all too common.

Indication of HGF

Its been suggested in the past that a blown radiator can indicate imminent HGF. The header tank cap is normally the first to vent when the system is pressurised since it only requires approximately 1 bar. The radiator is designed to operate at pressures a lot higher than this and the cap acts as a fuse. However, the header tank is on the lowest pressure point of the circuit and this allows high pressure peaks on the high pressure side (which is from the engine to the rad). need more thought here

Aftermarket Upgrades

There are basically three options available when it comes to after market radiators that will fit an Elise/Exige. All three are 'all aluminium' and none have the dreaded plastic end tanks. There appears to be only two manufacturers that are making these radiators. The 42mm single row is made by ??? and the 45mm twin row in single and triple pass is made by Pro Alloy. All on-line retailers sell the same radiators, they just badge them with different names to confuse you. Hopefully the following table will help when making your choice for purchase:

On-line Retailer	32mm Core/Single Row Manufactured by ???	42mm Core/Single Row Manufactured by ???	45mm Core/Twin Row Manufactured by Pro Alloy	45mm Core/Twin Row/Triple Pass Manufactured by Pro Alloy
Eliseparts	ALUMINIUM HIGH PRESSURE RADIATOR	Not available	ALUMINIUM UPGRADED RADIATOR	TRIPLE PASS RADIATOR
Eliseshop	Not available	Aluminium High Pressure extra capacity Radiator	Pro Alloy Full Aluminium Race Radiator	Not available
Pro Alloy	Not applicable	Not applicable	Alloy Race Radiator	3 Pass Race Radiator
Hangar 111	Not available	PERFORMANCE RADIATOR - 42MM CORE	TRACK DAY/MOTORSPORT RADIATOR - 45MM CORE	TRIPLE-PASS MOTORSPORT RADIATOR - 45MM TWIN ROW
Seriously Lotus	Radiator High Pressure 32mm	Radiator High Pressure 42mm	Not available	Pro-Alloy Radiator Triple Pass 45mm

Seriously Lotus appear to be the only on-line retailer that sells anything remotely different. For example they have 50mm two row triple pass, 32mm one row single pass, 42mm one row triple pass. See website for details. Elise-shop don't do the Pro-Alloy triple pass. They have a 42mm (single or double?) row triple pass instead.

The following video will help you understand some of the terms used in radiator speak, like twin rows, dual cores, triple pass etc:

• http://www.youtube.com/watch?v=Ldfuzy_JJUo

For comparison the OEM radiator is a 32mm single core, single pass. The triple pass radiators are only intended for motorsports and are not recommended for road use.

• 

  32mm core, single row, single pass

• 

  Failing 32mm core, single row, single pass

• 

  Standard OEM 32mm core, single row, single pass, with plastic end tanks

• 

  Pro Alloy 45mm core, twin rwo, single pass

• Pro alloy 45 2row 3pass.jpg

  Pro Alloy 45mm core, twin row, triple pass

Pro Alloy is run by SELOC member Wayne Clayden.

OEM Radiator

The original equipment manufacturer was PMA Group. Typically the plastic endcaps can be expected to be good for 3 years

http://www.pmagroup.co.uk/branches.php