Difference between revisions of "Remove the rear clamshell"

From TechWiki
Jump to navigation Jump to search
Line 4: Line 4:
 
add remove some of this (''add remove what?'')
 
add remove some of this (''add remove what?'')
  
if outside buy halfords small car cover £25
+
if outside buy halfords (''buy'') small car cover £25
  
soft/hard top wil need to be off
+
soft/hard top will need to be off
  
drive or lift car up onto a 6" concrete blocks
+
drive or lift (''definitely lift'') car up onto a 6" concrete blocks
  
 
disconnect battery black wire (nearest bulkhead)
 
disconnect battery black wire (nearest bulkhead)
Line 17: Line 17:
 
from inside cabin
 
from inside cabin
 
4 8mm bolts upwards
 
4 8mm bolts upwards
remove rool bar black plastic clip things for softtop catches - undo 2 allen bolts
+
remove rool (''roll'') bar black plastic clip things for softtop catches - undo 2 allen bolts (''from the'')
long tail shroud undo allen bolt at each end
+
long tail shroud (''shroud? think you mean soft top?'' undo allen bolt at each end
 
lift off shroud - leaves sticky foam on rear clam - where do you buy some more?
 
lift off shroud - leaves sticky foam on rear clam - where do you buy some more?
  
Line 24: Line 24:
 
it's only held in with 4 of those black plastic rivet things with heads that maul when you try to unscrew them
 
it's only held in with 4 of those black plastic rivet things with heads that maul when you try to unscrew them
 
so decided to remove passenger seat
 
so decided to remove passenger seat
and passenger seat belt top mount to clam shell
+
and passenger seat belt top mount to clam shell (''is this supposed to be a sentence?'')
seat is only held in by 4 sownward allen bolts (as above)
+
seat is only held in by 4 sownward (''downward?'') allen bolts (as above)
 
front 2 are easy to get to
 
front 2 are easy to get to
rear tunnel is ok if you have enough extensions
+
rear tunnel(''what tunnel??'') is ok if you have enough extensions
rear near side only if you have a flexible extension,and the bolt is so tight it you need to rotate the seat too, to help it release
+
rear near side only if you have a flexible extension,and the bolt is so tight it (''"tight it"? so tight that?'' you need to rotate the seat too(''Really? going to rotate the seat to unscrew a bolt?''), to help it release
 
( you'll need to remove the bracket holding the lumbar bubble thing too - allen head )
 
( you'll need to remove the bracket holding the lumbar bubble thing too - allen head )
 
ok then remove the trim panel undoing the speaker wires
 
ok then remove the trim panel undoing the speaker wires
  
all this for
+
all this (''is'') for
 
'''3. Remove bolt each side going sideways into the clam'''
 
'''3. Remove bolt each side going sideways into the clam'''
  
 
'''4. Remove engine cover'''
 
'''4. Remove engine cover'''
2 bolts each hinge with assorted washers
+
2 bolts each hinge with assorted washers (''that's LITERALLY not even a sentence'')
 
unplug the aerial near the engine cover
 
unplug the aerial near the engine cover
from inside cabin unscrew 2 nuts per hinge and remove hinge clamp brackets which hold down front of clam
+
from inside cabin (''seriously dude! define "cabin"'') unscrew 2 nuts per hinge and remove hinge clamp brackets which hold down front of clam
  
'''5. Have a rest and remove carpet foam etc from within boot'''
+
'''5. Have a rest (''from my terrible grammar'') and remove carpet(,) foam etc from within boot'''
remove battery bracket 2 bolts
+
remove battery bracket 2 bolts (''rest is over! back to the poor writing'')
 
2 more clam bolts through floor battery side
 
2 more clam bolts through floor battery side
3 clam bolts right side
+
3 clam bolts right side (''somewhere on the right side'')
discover tyre weld above offside wheel arch
+
discover (''"discover"? if you had to "discover" this you're an idiot'') tyre weld above offside wheel arch
  
'''6. Remove 2 allen bolts holding ecu unit to boot partition'''
+
'''6. Remove 2 allen bolts holding ecu (''you'll be able to discover this even if you can't discover the tyre weld'') unit to boot partition'''
leave ecu where it is
+
leave ecu where it is (''Where you discovered it'')
  
'''7. Remove n/s wheel ( jack car first)'''
+
'''7. Remove n/s wheel ( jack car first)(''no s**t, Sherlock'')'''
remove liner
+
remove liner (''After removing the following'')
 
remove half dozen of those screw plastic rivet things
 
remove half dozen of those screw plastic rivet things
 
remove one 8mm bolt just above shock absorber
 
remove one 8mm bolt just above shock absorber
  
 
lift liner over shock absorber - it's tight
 
lift liner over shock absorber - it's tight
easerest of wheel arch liner out of space - its a good job its flexible - I found back end easiest to get out first
+
easerest (''what?'') of wheel arch liner out of space - its a good job its flexible - I found back end easiest to get out first
 
and there's a clip holding some wires which you need to poke out from inside the wheel arch
 
and there's a clip holding some wires which you need to poke out from inside the wheel arch
  
 
this gives access to 2 bolts holding clam / air box tube/side grill towards front of wheel arch - there may be 'C' shims here!
 
this gives access to 2 bolts holding clam / air box tube/side grill towards front of wheel arch - there may be 'C' shims here!
 
from inside liner pull battery wires through clam with grommit
 
from inside liner pull battery wires through clam with grommit
same for rear lightcluter wires - undo connector in boot
+
same for rear lightclu(s)ter wires - undo connector in boot(.)
 
refit wheel lower jack
 
refit wheel lower jack
  
Line 74: Line 74:
 
'''11. You will need to unbolt the exhaust silencer hanger which is bolted to the clam near the N/S/R wheel'''
 
'''11. You will need to unbolt the exhaust silencer hanger which is bolted to the clam near the N/S/R wheel'''
  
'''11. Remove one more bolt each side at this point screwing sideways into the clam'''
+
'''11. Remove one more bolt each side at this point(''where??'') screwing sideways into the clam'''
  
 
lift off the clam
 
lift off the clam
Line 81: Line 81:
  
 
== Top tips ==
 
== Top tips ==
 +
 +
*Find somebody that can write in English, or at least sentences, to make a how-to guide. This was worse than useless because first of all, IT'S FOR AN S2!!! Secondly, I spent more time translating this guide than actually finding anything that I didn't already know.
  
 
*Not all the cars have the same fixings (early/late S1s for example) so there may be different / missing steps not mentioned here or in the service manual. Likewise, the service manual doesn't mention disconnecting the boot release cable from the clam, pulling free the co-located drain hose or that you have to prize the numberplate off to get to the rear centre attachment.  
 
*Not all the cars have the same fixings (early/late S1s for example) so there may be different / missing steps not mentioned here or in the service manual. Likewise, the service manual doesn't mention disconnecting the boot release cable from the clam, pulling free the co-located drain hose or that you have to prize the numberplate off to get to the rear centre attachment.  

Revision as of 17:24, 24 September 2017

Please upload a picture

A few of us are removing rear clam currently

add remove some of this (add remove what?)

if outside buy halfords (buy) small car cover £25

soft/hard top will need to be off

drive or lift (definitely lift) car up onto a 6" concrete blocks

disconnect battery black wire (nearest bulkhead)

Procedure

1. Remove roll over bar shroud from inside cabin 4 8mm bolts upwards remove rool (roll) bar black plastic clip things for softtop catches - undo 2 allen bolts (from the) long tail shroud (shroud? think you mean soft top? undo allen bolt at each end lift off shroud - leaves sticky foam on rear clam - where do you buy some more?

2. Remove speaker trim panel it's only held in with 4 of those black plastic rivet things with heads that maul when you try to unscrew them so decided to remove passenger seat and passenger seat belt top mount to clam shell (is this supposed to be a sentence?) seat is only held in by 4 sownward (downward?) allen bolts (as above) front 2 are easy to get to rear tunnel(what tunnel??) is ok if you have enough extensions rear near side only if you have a flexible extension,and the bolt is so tight it ("tight it"? so tight that? you need to rotate the seat too(Really? going to rotate the seat to unscrew a bolt?), to help it release ( you'll need to remove the bracket holding the lumbar bubble thing too - allen head ) ok then remove the trim panel undoing the speaker wires

all this (is) for 3. Remove bolt each side going sideways into the clam

4. Remove engine cover 2 bolts each hinge with assorted washers (that's LITERALLY not even a sentence) unplug the aerial near the engine cover from inside cabin (seriously dude! define "cabin") unscrew 2 nuts per hinge and remove hinge clamp brackets which hold down front of clam

5. Have a rest (from my terrible grammar) and remove carpet(,) foam etc from within boot remove battery bracket 2 bolts (rest is over! back to the poor writing) 2 more clam bolts through floor battery side 3 clam bolts right side (somewhere on the right side) discover ("discover"? if you had to "discover" this you're an idiot) tyre weld above offside wheel arch

6. Remove 2 allen bolts holding ecu (you'll be able to discover this even if you can't discover the tyre weld) unit to boot partition leave ecu where it is (Where you discovered it)

7. Remove n/s wheel ( jack car first)(no s**t, Sherlock) remove liner (After removing the following) remove half dozen of those screw plastic rivet things remove one 8mm bolt just above shock absorber

lift liner over shock absorber - it's tight easerest (what?) of wheel arch liner out of space - its a good job its flexible - I found back end easiest to get out first and there's a clip holding some wires which you need to poke out from inside the wheel arch

this gives access to 2 bolts holding clam / air box tube/side grill towards front of wheel arch - there may be 'C' shims here! from inside liner pull battery wires through clam with grommit same for rear lightclu(s)ter wires - undo connector in boot(.) refit wheel lower jack

8. Do same for o/s wheel after removing the liner undo the 8 screws holding the petrol filler aluminium ring aand press the filler cap gently - it should unstick and move slighly inside clam

9. I found it easier to Remove the rear undertray

10. Remove a pozi screw each side holding the grille around the exhaust

11. You will need to unbolt the exhaust silencer hanger which is bolted to the clam near the N/S/R wheel

11. Remove one more bolt each side at this point(where??) screwing sideways into the clam

lift off the clam

refit by reversing the above procedure :)

Top tips

  • Find somebody that can write in English, or at least sentences, to make a how-to guide. This was worse than useless because first of all, IT'S FOR AN S2!!! Secondly, I spent more time translating this guide than actually finding anything that I didn't already know.
  • Not all the cars have the same fixings (early/late S1s for example) so there may be different / missing steps not mentioned here or in the service manual. Likewise, the service manual doesn't mention disconnecting the boot release cable from the clam, pulling free the co-located drain hose or that you have to prize the numberplate off to get to the rear centre attachment.
  • Worth removing the edge finisher (rubber trim) around the air intake grills, they may be glued on and are attached to the rear clam and the sill panels. If they are glued and you try to remove the clam they will probably tear (although if they are glued you will probably have to replace anyway, part no A111U6034V).