Change a front wheel bearing

Time & Tools
Time:	Approx 1 hour - Assuming everything comes apart nicely and the outside bearing racer doesn’t snap off and stay attached to the hub flange - in which case you will need to carefully cut it off using an air grinder etc.
Tools:	17, 19 and 2 x 24mm Sockets 2 x Extension bars 2 x Big wrenches or Breaker Bars 17mm Spanner 8mm Hex head socket or Allen key Torque wrench Bearing circlip pliers Penetrating fluid Hydraulic press (at least 10 tonne) Duralac Threadlock or Pipe Sealer Toothbrush CV Grease Fine Sandpaper Oven

Preparation

Before you start, take your new wheel bearing and pop in the freezer until required! This will ensure the bearing is as small as it can be prior to fitment!

Replacing the bearing

1. Whilst the car is sitting on the ground, pop the wheel cap off and using a breaker bar and a 24mm socket crack the torque off the M16 Clamp bolt as this is tightened to 210Nm.

Loosening the M16 Clamp bolt

Jack up the car and remove the wheel. Whilst it’s off you may also wish to take the opportunity to clean it thoroughly.

2. Remove the 2 bolts holding the calliper to the hub body using an 8mm hex socket or Allen key. (bolt to be re-installed using thread lock or pipe sealer and tightened to 45Nm

Calliper bolt locations

Providing your discs are not too badly worn, you should be able to extract the calliper complete with pads without having to remove the pads. Ensure the calliper is suspended to prevent any damage to the brake pipe work. Next remove the brake disc.

Brake disc and calliper removed and properly supported

3. Remove the M16 Clamp bolt using a 24mm socket on each side

M16 Clamp bolt removed

4. Now loosen all 6 bolts retaining the steering arm and bottom ball joint plinth. 2 x 8mm hex bolts on steering arm, 4 x 17mm bolts on the bottom plinth.

5. Remove the 4 x 17mm bolts attaching the bottom plinth, note a 17mm spanner will be necessary for the front 2 bolts do to limited clearance for a socket. When these bolts are re-installed they should be tightened to 45Nm, thread lock applied to bolts and Duralac applied to the plinth to prevent corrosion.

Lower hub bolt locations

Removing the front lower hub bolts with a screwdriver

It may be necessary to prize the hub from the plinth with a flat screwdriver as previous application of duralac will cause them to stick together.

Prizing the hub and plinth apart

Once separated, apply Duralac to the plinth

6. Remove the 2 x 8mm hex bolts connecting the steering arm ensuring you catch any camber shims that fall out, note Duralac again should be applied to the nearest shim to the alloy hub and bolts re-installed at 45Nm with thread lock.

Steering arm bolt location, when removing watch for camber shims

Apply Duralac to the shim touching the alloy hub

7. Now the hub is removed the specialist tool and part where you make your missus very angry begins.

Spray the bearing and inner hub carrier thoroughly with penetrating fluid and leave a few minutes to soak.

Hub removed

Hub sprayed with penetrating fluid

Using a socket which is slightly smaller than the inner bearing shaft of the hub flange suspend the hub flange facing down and press the flange free of the bearing assembly.

Pressing the flange shaft out from the hub

Ensure none of the wheel studs do not contact the stand base or they will be pressed from the flange too.

The removed flange shaft

Clean the flange shaft and if necessary use the fine sand paper to remove any corrosion, apply a tiny bit of grease to aid re-assembly once the bearing has been replaced.

8. Clean the hub assembly thoroughly and remove the 2 cir-clips front and rear using special cir-clip pliers.

Removing the cir-clip

Pre-heat an oven to 90degrees and place the whole hub on a piece of greaseproof paper for 20 minutes.

After 20 minutes, remove the hub spray some more penetrating fluid on the bearing itself, this will cause the bearing to cool quicker whilst the alloy is still warm.

9. Pop the whole assembly in the press with the flattest side facing down, allowing space beneath for the bearing to drop clear. Using a large socket to press the bearing clear.

Pressing out the old bearing

10. Clean the inside of the empty hub including the cir-clip recesses, apply a thin smear of grease to the inside of the hub, re-install the inside cir-clip.

Remove the wheel bearing from the freezer, apply a thin smear of grease to the outside of the bearing and seat on top of the hub and using a flat surface on top press the bearing as far home as you can until your flat surface touches the hub body.

To finish pressing the bearing the remainder of the way, it is Important the bearing is pressed home by its outer body to avoid damage to the inner bearing (as pictured) obviously this object needs to have a smaller diameter than the inner hub walls otherwise it will end up attached to the hub too.

Outer bearing area marked

I ground down the old bearing to make a slightly smaller diameter and used this to finish pressing the new bearing home to the installed cir-clip.

Pressing in the new bearing

11. Re-install the final cir-clip and the bearing replacement is complete.

Cir-clip and bearing refitted

12. Re-press the hub flange home being careful to support the bearing on the inner race to prevent damage. Ensure you press this home the correct way round, as shown.

Pressing in the hub flange

13. Re-install the hub, plinth, steering arm and brakes as per guide above.

14. Stand back and admire your handy work!

Voila!

More photos and info in this post

http://forums.seloc.org/viewthread.php?tid=353090&page=1#pid5976460