Difference between revisions of "Fit a harness bar and belts"

From TechWiki
Jump to navigation Jump to search
m
m
 
(17 intermediate revisions by 6 users not shown)
Line 1: Line 1:
−
'''1)''' Remove seats (and the inertia belts at this point if you plan not to keep them).
+
Harnesses greatly improve the feel of the car on track and lock you into the seated position.  The installation is relatively common no matter which [[harness bar]] or belts you choose.
  
 +
== Procedure ==
 +
# [[Removing the seats|Remove seats]]
 +
#: (and unscrew the inertia belts from the seats at this point if you plan not to keep them).
 +
# Remove plastic trim
 +
#: (and the intertia belt spool, if applicable).
 +
# Loosely screw harness bar in place.
 +
# Stick masking tape onto the rollover bar at the top and bottom of the circular section of the harness bar where it meets the rollover bar (hard to explain but is very simple).
 +
# Remove the harness bar
 +
# Loosely put the plastic trim in place and, using the masking tape on the rollover bar as a guide, mark the top and bottom of the harness bar onto the plastic trim.
 +
# Remove the plastic trim and cut away the trim so that it can fit back in place with the harness bar fitted.
 +
# Put the plastic trim loosely back into the car.
 +
# Slide one end of the harness bar *past* the fixing point on the rollover bar so that you can then get the other end of the harness bar past the other side of the rollover bar.
 +
# Bolt the harness bar to the rollover bar. You'll need a 17mm socket/spanner and should be able to pass the socket/spanner from below if the original belts are removed. If you want to keep the original belts, put them back in before fixing the plastic trim.
 +
# Fit the plastic trim properly in place
 +
# Attach the shoulder harnesses to the harness bar.
 +
# Attach the lap harnesses to the seats. I removed my inertia reel belts so this was really easy.
 +
# Bolt the seats in
  
−
'''2)''' Remove speakers.
 
  
 +
[http://www.aouv49.dsl.pipex.com/IMG_2389.JPG Picture 1] Please note, photo incorrect, holes should faces downwards, not upwards as pictured.
  
−
'''3)''' Remove plastic trim (and the intertia belt spool, if applicable).
+
[http://www.aouv49.dsl.pipex.com/IMG_2391.JPG Picture 2]
  
 +
[http://www.aouv49.dsl.pipex.com/IMG_2392.JPG Picture 3]
  
−
'''4)''' Loosely screw harness bar in place.
+
[http://www.aouv49.dsl.pipex.com/IMG_2398.JPG Picture 4]
  
 +
[http://www.aouv49.dsl.pipex.com/IMG_2395.JPG Picture 5]
  
 +
== Information and Pictures Provided By ==
  
−
'''5)''' Stick masking tape onto the rollover bar at the top and bottom of the circular section of the harness bar where it meets the rollover bar (hard to explain but is very simple).
+
[http://forums.seloc.org/member.php?action=viewpro&member=PhilS PhilS]
  
 +
http://forums.seloc.org/viewthread.php?tid=8428
  
−
'''6)''' Remove the harness bar.
+
[http://forums.seloc.org/member.php?action=viewpro&member=Steve+S2 Steve S2]
  
 +
http://forums.seloc.org/viewthread.php?tid=21495#pid312060
  
−
'''7)''' Loosely put the plastic trim in place and, using the masking tape on the rollover bar as a guide, mark the top and bottom of the harness bar onto the plastic trim.
+
== Discussion ==
  
 +
Discussion on the merits of harness fitting options
 +
http://forums.seloc.org/viewthread.php?tid=166724&page=1
  
−
'''8)''' Remove the plastic trim and cut away the trim so that it can fit back in place with the harness bar fitted.
+
[[Category:DIY]]
−
 
+
[[Category:Safety]]
−
 
+
[[Category:Interior]]
−
'''9)''' Put the plastic trim loosely back into the car.
+
[[Category:Lotus Elise]]
−
 
+
[[Category:S2]]
−
 
 
−
'''10)''' Slide one end of the harness bar *past* the fixing point on the rollover bar so that you can then get the other end of the harness bar past the other side of the rollover bar.
 
−
 
 
−
 
 
−
'''11)''' Bolt the harness bar to the rollover bar. You'll need a 17mm (?) socket/spanner and should be able to pass the socket/spanner through the speaker mounting point in the plastic trim to tighten the bolts. This is a pain in the arse and I sliced my wrists to pieces in the process.
 
−
 
 
−
 
 
−
'''12)''' Fit the plastic trim properly in place
 
−
 
 
−
 
 
−
'''13)''' Attach the shoulder harnesses to the harness bar.
 
−
 
 
−
 
 
−
'''14)''' Attach the lap harnesses to the seats. I removed my inertia reel belts so this was really easy.
 
−
 
 
−
 
 
−
'''15)''' Put the speakers back in. It's a hassle putting the screws back in because the harness bar is very close to the speakers. I ended up using a very very narrow flatheaded screwdriver at a very jaunty angle to the screw head to do this.
 
−
 
 
−
 
 
−
'''16)''' Bolt the seats in
 
−
 
 
−
 
 
−
[http://www.aouv49.dsl.pipex.com/IMG_2389.JPG Picture 1]
 
−
 
 
−
[http://www.hubert.racegame.org/brakes.html Picture 2]
 
−
 
 
−
[http://www.hubert.racegame.org/brakes.html Picture 3]
 
−
 
 
−
[http://www.hubert.racegame.org/brakes.html Picture 4]
 
−
 
 
−
[http://www.hubert.racegame.org/brakes.html Picture 5]
 

Latest revision as of 15:49, 15 May 2008

Harnesses greatly improve the feel of the car on track and lock you into the seated position. The installation is relatively common no matter which harness bar or belts you choose.

Procedure

  1. Remove seats
    (and unscrew the inertia belts from the seats at this point if you plan not to keep them).
  2. Remove plastic trim
    (and the intertia belt spool, if applicable).
  3. Loosely screw harness bar in place.
  4. Stick masking tape onto the rollover bar at the top and bottom of the circular section of the harness bar where it meets the rollover bar (hard to explain but is very simple).
  5. Remove the harness bar
  6. Loosely put the plastic trim in place and, using the masking tape on the rollover bar as a guide, mark the top and bottom of the harness bar onto the plastic trim.
  7. Remove the plastic trim and cut away the trim so that it can fit back in place with the harness bar fitted.
  8. Put the plastic trim loosely back into the car.
  9. Slide one end of the harness bar *past* the fixing point on the rollover bar so that you can then get the other end of the harness bar past the other side of the rollover bar.
  10. Bolt the harness bar to the rollover bar. You'll need a 17mm socket/spanner and should be able to pass the socket/spanner from below if the original belts are removed. If you want to keep the original belts, put them back in before fixing the plastic trim.
  11. Fit the plastic trim properly in place
  12. Attach the shoulder harnesses to the harness bar.
  13. Attach the lap harnesses to the seats. I removed my inertia reel belts so this was really easy.
  14. Bolt the seats in


Picture 1 Please note, photo incorrect, holes should faces downwards, not upwards as pictured.

Picture 2

Picture 3

Picture 4

Picture 5

Information and Pictures Provided By

PhilS

http://forums.seloc.org/viewthread.php?tid=8428

Steve S2

http://forums.seloc.org/viewthread.php?tid=21495#pid312060

Discussion

Discussion on the merits of harness fitting options http://forums.seloc.org/viewthread.php?tid=166724&page=1

Retrieved from ‘https://wiki.seloc.org/index.php?title=Fit_a_harness_bar_and_belts&oldid=7082’