Search results

This is how to remove the centre console on an S2 (typically a 111R or exige) it may differ for rover engine cars or later models. Make sure the car is ...er close to the floor. An allen key will work in a pinch if you don't have a torx set. So that is two screws to remove up front - the shiny silver ones

A DPM is a topic that has been posted more than once on the forums. It stands for 'Dou ...fortunate story of an Exige driver whose car was wrecked by an employee of a valeting company.

...Exige to sign off with Final Edition models]</ref>. Set to be replaced by a new model known as Type 131 and was announced as being the last internal co ...agram @Lotuscars - Code]</ref>, which was announced as the Emira amongside a handful of teaser images during the [https://drivingtomorrow.lotuscars.com/

Prestige sell a full range of covers made in house and from many other suppliers, including ...anywhere else, just get in touch with Chizzler43 on here and you will get a better deal.

[[Category:S2 Exige]] So you have probably arrived here searching for a quick fix for your saggy headlining. I have good news and bad news for you.

...Elise 111R, but it's probably very similar for other models. If you go to a dealer to get this done they do it the correct way by taking the whole dash The part number needed is A116M6048F. You can get this from a Lotus dealer - I paid £38.71 from Lispcomb.

Make sure you buy a tyre pressure gauge of your own, who knows when the last time the air pump ...part of your suspension setup and the pressure numbers from the manual is a good start if you run factory geo and OE tyres. Anything else is trial and

...eed settings from the same nominal 12V input. It has three 12V inputs and a single output, which is the motor feed. Image:InsideResisterPack.jpg|Resister pack taken apart. It's just a crude coil assembly giving resistance.

=Elise and Exige S1= ! Exige

So quite a few people have installed a powered subwoofer so I'm not claiming to be the first, it's just there's no ...the dash in the pax footwell. It seems the facelift dash (I have a MY2010 Exige) won't easily support something suspended from beneath the pax airbag so th

...formance is poor until the discs are dried by application. (From VIN 2260 a splash guard was introduced to reduce this problem - Source [http://www.eli ...ction generated is mostly Adherent Friction rather than abrasive friction (a very good article on the nature of braking can be found [http://www.stoptec

...usly known as Response Super DOT 4) brake fluid, changed annually. This is a fully synthetic brake fluid that exceeds the boiling point specifications o ...t to note that it is '''React Performance DOT 4''' as Castrol do also sell a normal DOT 4.

...ce cars. They make aftermarket and some OEM units for the Juno, the Elise, Exige, 340r from Lotus, the new Caparo T1, Caterhams, Radicals etc, and can give ...ers, with developments being incorporated into the latest products. So as a result of the modular design, the top end components are included right thr

...otus dealers quoting thesecurity codes, and are normally obtainable within a few days. ...wnership, to request from Lotus a factory record archive search, for which a small charge is made.

== Pro Alloy Charge Cooler Install - Exige S2 == ...nsive installation guide... but it should be DIY'able with basic tools and a few extras.

...that the only way to mix tyres is with a pair of P Zeros on the front and a pair of C-Drives on the back. Details are on the Lotus web site at http://w These wheels were replaced in April ’99 by a 12 spoke design made by Rimstock,

...uperior performance, both in terms of stopping power and longevity, and at a more reasonable costs. ...DIY project, and some people prefer the reassurance this gives. There is a '''[[Brake pad bedding in procedure]]''' which you are encouraged to follow