Search results

• Diy black wheels
  '''Stage 1 (Removing old paint)'''
  2 KB (386 words) - 14:16, 19 January 2012
• Change a ball joint
  {{Infobox Timetools | time=1 hour | tools=[[Ball joint splitter]], spanner, jack}} '''1. Raise car and remove front wheels'''
  5 KB (916 words) - 12:34, 30 May 2013
• Replacing S1 front near-side brake pipe
  - Union 1: BN3 10mm x 1mm standard male
  1 KB (197 words) - 19:43, 4 July 2014
• Newsletter Issues
  {| border="1" | [http://news.seloc.org/1/ October 2004] || 10/2004 || '''Welcome''' - Welcome to the first monthly
  14 KB (2,178 words) - 22:35, 27 August 2011
• Steering Wheel - Evora
  '''Step 1''' - '''DISCONNECT BATTERY FIRST !!!!!'''
  2 KB (327 words) - 00:03, 6 November 2012
• Engine Control Unit
  {| border=1 cellpadding=5 cellspacing=0 | Elise S1 (120bhp) || MEMS 1.9 || proprietary || LotusScan (Connector SAE J1962)<br />or Rover Test-Book
  6 KB (945 words) - 15:04, 13 January 2020
• LED Sidelights
  1. An early S2 with H1/H7 headlamp cluster (inside wheel arch liner AND front
  1 KB (195 words) - 22:17, 23 May 2014
• Radiator
  {|border=1 {|border=1
  7 KB (1,029 words) - 23:11, 5 February 2017
• Bulbs
  Bulbs as fitted as standard to Series 1 Elises/Exiges. <table cellspacing="0" cellpadding="3" border="1">
  5 KB (894 words) - 22:16, 17 February 2023
• Shimming the Powertrain PG1 gearbox
  ...you have measured the shaft end play without shim pack. In my case it was 1,68 mm. ...her should be allowed to take up. In my case it summed up to 0,83 + 0,17 = 1,00 mm.
  8 KB (1,467 words) - 20:21, 25 April 2014
• Misfire
  ...f the injectors. Tell tale signs can include rusty spark plugs on cylinder 1 and 4, sometimes even all four, lumpy idle or misfiring, high emissions, je
  2 KB (230 words) - 19:10, 5 September 2011
• Fit a HID kit
  '''1. [[Remove the headlamp cover]]''' Next up, poke through the rubber grommet from inside (1) and trim the inner edge a little (2) to free things up a little for when i
  6 KB (944 words) - 19:38, 13 February 2015
• Toe alignment using straight edges
  The toe-in of each straight edge can therefore be calculated to: 30/3998=1/133 mm ⁄ mm ...ans that for every mm you go forward along the straight it goes inwards by 1/133 mm.
  5 KB (924 words) - 21:26, 19 April 2020
• Additional power outlet for S1 dash
  1. Check that the right-hand most "switch" in your light panel is a dummy. I ...ch was. It will work best if you offset the template to the right by about 1-2mm. Don't go too far though otherwise the switch surround won't go back o
  4 KB (654 words) - 14:03, 18 June 2014
• Geo Alignment Rig (Home Made)
  1. Homebase for two bits of 2400mm rigid aluminum (16mm ally channel as they 1. To measure camber I made a plumb line out of stuff lying around (net curta
  6 KB (1,004 words) - 01:13, 6 March 2017
• Central Locking Module Replacement
  [[Image:CDLModuleReplace3.jpg|left|thumb|Move vent hose 1]] [[Image:CDLModuleReplace5.jpg|left|thumb|Module 1]]
  4 KB (742 words) - 13:34, 19 January 2012
• Fusebox
  {| cellpadding="8" cellspacing="0" border="1" |1
  16 KB (2,482 words) - 13:02, 5 February 2023
• Geo Setups
  {| border=1 cellpadding=5 align=center ...2 || 130/130mm || +3.8° || -0.1° || 0.2mm OUT Overall [-0.03°] || -1.8° || 1.2mm IN each side [0.16°]
  7 KB (957 words) - 14:44, 4 August 2023
• Tyre pressures
  {| border="1" {| border="1"
  8 KB (1,241 words) - 16:23, 23 August 2021
• Installing an oil pressure/temperature gauge in S2
  ...his installation at http://forums.seloc.org/viewthread.php?tid=171330&page=1#pid3347959 1. Mute selecter: Set key hold after power on
  6 KB (1,086 words) - 15:09, 17 March 2012

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)