Search results

Jump to navigation Jump to search
  • • remove the front grill - two posidrive screws on my 111S, these where very rusty and needed a very well fitting screwdriver to get t
    4 KB (741 words) - 10:39, 3 May 2010
  • The Elise S1 111S 143bhp EU2 VVC is controlled by the MEMS 2J ECU common with the early VVC M The Elise S2 111S 156bhp EU3 VVC is controlled by the Lotus K4 ECU A117M0109F (which looks th
    11 KB (1,938 words) - 17:53, 19 September 2011
  • The 52MM Throttle body came standard fittment on the Elise S2 111S (and also included as part of the Lotus drivability kit for the S1 Sport 16
    2 KB (421 words) - 11:41, 10 October 2019
  • ...ition where normally the radio is on but ignition is still off). On a 2004 111S, (and probably other years and models too), it has to be in position 2.<br/
    3 KB (539 words) - 08:34, 7 April 2024
  • S1 111S - K-series VVC with 143bhp '''S2 111 and 111S'''
    7 KB (1,101 words) - 04:39, 3 March 2018
  • Bearing Failure for S2 111s and other model with 4-2-1 exhaust: A few notes from having done this recently to a 111S - clem2k3
    11 KB (1,968 words) - 11:05, 3 July 2023
  • | image = [[Image:Elise-Wheel-grey.jpg|thumb|S2 111S OEM Wheel]] | notes = OEM S2 111S wheels, also available in black
    14 KB (1,847 words) - 18:10, 7 August 2017
  • *Cybex Solution-Z: Good fit in an S1 111S, as with the Solution-S above, the ISOFIX connectors fold into the base of
    4 KB (673 words) - 21:44, 14 August 2022
  • ...se Shop wiper with integrated spraybar. Here is how I did it on my 2005 S2 111S:
    7 KB (1,229 words) - 14:53, 6 February 2012
  • ...is screw may be a Torx type. Use a T20 driver to remove (it was on a 2003 111s) - (T15 Torx key worked on 2005 111R)
    7 KB (1,220 words) - 00:49, 15 January 2012
  • whilst the 111S model featured a 6 spoke design by O.Z. with ½” wider (7.5J) rear rims. == Car/tyre Details:- S2 111s/Bridgestone RE040==
    37 KB (5,161 words) - 16:18, 12 August 2021
  • ! 111S
    8 KB (1,036 words) - 12:26, 5 July 2023
  • At least my 2004 S2 111S had a GM mirror with the ball joint on top of the mirror. It is a whopping
    6 KB (1,056 words) - 09:46, 9 September 2014
  • | Elise S1 111S || MEMS 2J || proprietary || LotusScan (Connector SAE J1962)<br />or Rover
    6 KB (945 words) - 15:04, 13 January 2020
  • ...0 less rpm on this installation. The kit will fit all MK1 Elise (including 111S and Sport 160) and features copper nickel plated mounting bracket, foam air ...it will fit all Mk2 Lotus Elise models with the K Series engine (including 111S) and features bright silver annodised aluminium mounting bracket, cold air
    18 KB (2,993 words) - 15:25, 16 June 2023
  • The Sport 135, Sport 160, Sport 190 and 111S models were supplied with iron disks which were vented and cross drilled. ...40R, were fitted with the same cross drilled disks as seen on the Series 1 111s and Sport 160 editions described above.
    14 KB (2,435 words) - 16:46, 7 May 2022
  • variations (35 cars): 111S wheels, tyres & spats; black painted fuel filler cap; matt finish alloy gea ==Elise 111S: January ‘99==
    37 KB (5,408 words) - 04:47, 25 February 2018
  • ...r. (I managed to use a chain removal tool successfully on the K Series, S2 111S)
    5 KB (906 words) - 17:29, 19 June 2019
  • * If you have a 111S you may need to loosen the clip that holds the throttle cable to the inlet
    7 KB (1,299 words) - 23:05, 4 November 2019
  • | steve 111s
    8 KB (1,336 words) - 21:27, 5 April 2021

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)